Reef Angel Forum

Got it figured out. A powered serial connection is still required when uploading code.

via Windows the USB-ttl cable is my only connection. I take the controller offline when I go to my PC.

I am sure it is COM4. I confirmed it in the Device Manager, removed the USB, readded it. All this occurred in Windows 10. Weird thing, I separately went to my Mac and tried the same upload. The Mac laptop allows me to keep the controller powered through its serial port while the TTL cable is plugged...

I'm unable to upload after using the wizard. Why would I get this message below? Assistance appreciated. The following features were automatically added: Watchdog Timer Version Menu The following features were detected: Simple Menu Binary sketch size: 24,056 bytes (of a 258,048 byte maximum) C:\Prog...

That did it. Thanks!

I'm using the Wizard to refresh my code but it won't compile! My setup is relatively simple, I am programming the relay plus an AISOL in the Low port. Compiling gives me a Lightsoverride error. I searched through all the forum and from a topic related to a Jebeo I tried a the few lines of code they ...

Successful desolder and replacement. Thanks for the customer support.

Most joystick functionality restored. Cleaned it with electrical contact cleaner and 3 of 4 vectors are stable. Resoldered the battery holder, so now the battery can do its job. Is it possible to replace the joystick if needed?

I recently uploaded code generated from the wizard and now my Aqua Illumination lights will not shut off and my moon cycle is gone. The Aqua Illumination lights are connected to the Low ATO communication port. I have selected the AI cable attachment in the wizard. I chose the parabola setting for al...

If I use the joystick on my RA Controller Plus it has a difficult time turning itself off even though it has returned to center position. The result is rapid cycling on the display and it is effectively unusable. In time the cycling stops, but I want the controller reliability back again. Are there ...

No blue, just slow green blink in the scenario below. Wifi Status Associated: true Authenticated: true DHCP: false IP address and port: 0.0.0.0:2000 ...Trying to connect to your router. My enabled DHCP range is 192.168.1 to 192.168.1.199 I can disconnect and repeat the procedures a few times and occ...

The wifi utility displays 0.0.0.0 as my WIFI add-on address when assigning an SSID and password through the wifi utility. That obviously does not attach to any home wifi. I can reset the firmware to default, but that doesn't help much. The best it will give occasionally is another address (192.168.1...

I found a breakthrough to the issue of a phantom wifi connection to my RA. To refresh the problem, the green light on the wifi module appears normal so the RA acts like it is connected, but my router says it is not connected. Disconnecting the module per published protocol results in a a short-term ...

So, is there anything wrong based on my get e or the client error log? Just looking for an assessment before install an additional WIFI access point onto my home network. I do have an ethernet connection in my aquarium room begging to be used, too bad there isn't a module for that. *****1/29/2013 7:...

I have the client installed on a Windows 8 desktop. I mainly use the portal and the iphone app at this time. As I write this the wifi is working. I pulled the wifi module to perform the "get e". After I connected it to my laptop, My router recognized the connection as on. I then plugged th...

CMD <2.38.3> get e WiFly Ver 2.38.3, 01-15-2012 on RN-131 Beacon=100 Probe=5 Reboot=0 OPEN= CLOSE= REMOTE= FlushSize=450 MatchChar=0 FlushTimer=10 IdleTimer=3 CmdChar=$ IF=UP DHCP=ON IP=192.168.1.84:2000 NM=255.255.255.0 GW=192.168.1.254 HOST=198.171.134.6:80 PROTO=TCP, MTU=1524 FLAGS=0x6 TCPMODE=0x...

I'm new here and this is my first post. I'm having a similar wifi problem. I need some outside help and this post was most similar to my problem. The green light on the WIFI module is on, and blinking slowly, but my router shows the module is OFF (i.e. not connected). So, I can't receive any updates...