Reef Angel Forum

Oh.... didn't see any mention of that in this thread. That stinks

Are there upgrade options from the RA+ to the RA*? I have everything but the head unit, I suppose.

That did the trick! Got the skill installed, but I'm getting device is unresponsive. I have the Wifi adapter, not the cloud adapter. Is that a problem?

It also only discovered my second relay box, not the first.

Just tried again hoping this would clear itself.... no dice. Still the same issue.

I just tried this myself and ran into an error trying to login. 277429D6-6A8E-4ACE-B5B8-D9BF0A877742.png I confirmed my username and password were correct by logging into the forum to double check. Same error comes up using Alexa app, Safari and Firefox. This is on ios12, not that I think that’s the...

I should add I have the Reeflink, if that makes it better.

I know the old RF module has been retired, but I’m wondering if anyone has figured out a solution for controlling EcoTech devices another way. Maybe a connection to EcoSmartLive? I’m picking up some used equipment today and thinking about control. Right now I just have a Radion which doesn’t need an...

Loads in a flash now. Thanks!

I’ve been noticing that graph data takes longer and longer to load both in the iOS app and using the U-App. It is to the point t where even after minutes I can’t get the data. Is this being phased out?

Darn.... I have it plugged in via an extension cable. Maybe I'll try and pull that first and see if it helps.

I have two bits of strange behavior that I haven't been able to figure out. 1. Occasionally, my RA will stop reading temperature and will report out at 0. Sometimes a simple reboot from the iOS app fixes it, sometimes unplugging it does it. Other times it requires doing that repeatedly. This is a pr...

The sensitivity varies by heater manufacturer and even from heater to heater. I set my heater 1F above what I want it to be and use the RA to cycle it on and off. I've found the RA is reliable to about 0.5F, much under that and you get chatter on the heater relay.

Thanks! I appreciate you sharing that code. I've added everything (I think) and my PDE compiles. So that's a good start :) Questions: 1. My dosers put out 1.1mL/min. It would then hold that I should set CalDP1Vol = 11 and CalDP1Time = 600 right? 2. Can I adjust DP1Volume from the iOS app? 3. How do ...

My ultimate goal is to be able to adjust the volume dosed for both alk and calc from the iOS app using internal memory.

I'm adding a BRS two-part dosing system to my tank this weekend. I just got the relay expansion module so I can use my spare relay box for the extra outlets. I'd like to be able to adjust the volume I dose, not set the dosing time and repeat interval. I pulled some code from lenovo's PDE that I thin...

I used to run this same driver using the original RA. If you are measuring 9.97VDC and the driver doesn't work, the issue isn't with your RA. Are you sure you wired the driver correctly? I doubt this is a current issue. I always put 10k current limiting resistors which would drop the current to 1mA ...

Portal shows the correct IP address as does the app. I can reach the RA onboard webserver from inside and outside of my local network. Here's a picture of my port forwarding setup. Seems OK to me.... Reef Angel wifi address: <My IP> My reefangelid:icecool2 Connection Status:Unreachable Address Last ...

Port forwarding looks OK. I should have updated my post a bit before I bumped it.... There are updates to the portal every few minutes, but I'm unable to control my tank from it. Something about an invalid Wifi address. On my iPhone the app never updates. If I try and switch a relay's state, it phys...

Bump.

Still having the issue with the portal and on the app. Any ideas?

Thanks. Is that in for the next update of the Wifi manual? :) Also, I still can't seem to get a working copy of the wifi utility for the mac. It could be on my end, but do you know if the current version works? I also had my connection drop suddenly. I can't tell if it is my router or the unit. If I...

OK, I got it working. I needed to set the autojoin flag. The command is "set wlan join 1"

Now it connects straight off when it boots. Is that in the directions, I don't think it was.

A little more info.... I was able to get the module onto my test network and onto my secure network. BUT I have to manually tell it to join with the "join <network>" command. When I unplug it from the USB and hook it back up to my RA, it does not connect to the network after it reboots.

I just got a wifi module and I'm trying to set it up. When I attempt to launch the Wifi Utility, my mac says the file is broken and trashes it. I redownloaded the DMG and the same thing happened. Is there somewhere I can pull an older version from? I'm able to connect to it through a terminal app, b...

Crud! I should have checked that before I bought the cable

For the price, I might just pick up the Kessil spectral controller... Crud crud crud...

Thank you. OK, it wasn't my code that was the problem. I'm recalling something about a booster jumper, but not the specifics. I think I must be in an alternate mode to what I need. I was running this for PWM output previously, but now I need 0-10V. Isn't there a jumper for that? Sorry, it's been lik...

I'm looking for a quick way to test my Kessil's functionality. I'd love to be able to do a repeating sunrise/sunset cycle that lasts 60 seconds. Is there an existing test file (I searched and didn't find one) or a quick few lines of code I can run?

Sorry, I don't have a schematic handy. I have a current limiting resistor on the signal line from the RA to the driver. On the driver side, I have the digital ground separated from the analog ground and joined with a small bridge. There is also a weak pull up on the driver as well. I have the GND fr...

That's what the problem was. I manually set the value.

I figured out about having to close the Arduino IDE. That was annoying.

Is the current version on Github stable? Maybe I checked out a working copy of it. I can't get my display to come up now. The red status LED is constantly lit. If I hold the joystick up, I can see the screen blink on and off. Not sure if I just pulled an unstable release or not.