Reef Angel Forum

I’m trying to do a water change and I can’t manually control anything. I have a red flashing light on my head unit, so I did some research and found that it’s a bus lock. I started disconnecting each expansion one by one but still had a problem. Only thing I had plugged into the expansion hub was my...

Well I diagnosed it down to a bad driver that was causing the issue. When I ordered the new dimming expansion and started hooking up the leds one at a time the problem happened when I touched one set of light to the expansion. So I reset everything and left that one out of the loop and got all light...

I have it the same as I had in the past. Turn on at 77.0 and turn off at 77.1. Since I redid the code it hasn’t been working right. Like right now my tank is at 77.3 and the heater is on.

now that I have reprogrammed my controller after dealing with my lights issue my heater doesn't shut off when it gets above the desired temp. ive tried setting it to all three temp probes and none of them turn the heater off. I set the code up with the internal memory. here is the code I have loaded...

ok im thinking its something with my dimming expansion. i just came home from work and all lights should be off but one set of blues was still on. i pulled up the app and went to the dimming over ride and everything was sitting at zero so i moved one up and the light came on but when i moved it back...

I have salinity, relay, expansion hub, dimming

The time keeps changing on the controller. Every time I sync it to my phone it stays for less then a minute then it all of a sudden changes to some random time in the night

I tried syncing it with my phone and the lights kicked on for about 30 seconds then went off again and my pumps for mixing kicked on. Those are on outlets set to always on and I toggle them off when not using them. So it’s like it’s reseting on its own for some reason.

When I got up this morning my lights weren’t on on my tank so I checked the connections and everything was fine so I pulled up the reef angel app and under the dimming all my lights are on zero. When I go to over ride I get about 3 turned on and all of a sudden all the lights reset to zero. What wou...

I accidentally deleted it off my phone now I cannot find it in the App Store. Did it get removed?

Ok that did the trick thanks for the help

No I've had these for awhile and they all worked then bam all three just read zero

Just tried reloading program and still no luck.

I have 3 temp probes and all three all of a sudden are reading 00.0 I reset the controller with no luck. What would cause all 3 to read 00.0?

Ok I thought that was the standard relay. Been awhile since I did the initial setup on one. If I delete the reefangel.feedingmodeportsE part of the code it should work fine correct?

Disregard I had that relay turned off on my app so it wasn't allowing it to kick on. Amazing how it works when you flip that switch to auto.

Got the new float switches and it's still not working. When I move the floats it toggles shows the sensors are working on my screen, it's just not kicking the pump on for some reason.

Recently my float switches aren't kicking my ato pump on when it gets low, having to do it manually through the app. Is it normal for them to stop working could it be the connection in the motherboard? I just ordered new switches in hopes that it fixes the issue. I know I pushed down on the connecti...

Well I replaced the small tube but it still won't pull the fluid from the container without assistance, and it still drained back once I get it pulled through.

Should there be some kind of lube on the tube?

Is that the tube that's $6 a ft? I was wondering why it was so short.

Where do you get that size tube?

Also it won't pull the fluid up the tube at first. I have to syphon it up to the pump then it will begin to move it.

Not sure how long it takes to lose the vacuum. I pulled it apart to see if the small tube inside was damaged, looked a little flat. Not sure if the tube isn't being pinched off enough by the rollers or what. I've replaced both lines going into and coming out of the pump. Only thing I haven't done is...

I have 2 dosing pumps, one for vinegar and one for kalk. The one that doses kalk won't stay primed, it slowly drains back to the container. The vinegar one seems to work fine. Is there some issue with the one that can be fixed?

Thanks that worked. Now I have to redo my temp probe codes

I just got a new temp probe when I plugged it in and pulled up the app it's still showing 0.0 I shouldn't have do anything with coding to get a reading do I?

Just did the update and it seems to work fine.

So do we know if the app will work with the new IOS 10. I know the old app had issues when they released a new operating system. Just want to make sure we don't have that problem again.

No I ended up rebooting my router and it started working again. So I think it's just my router/internet.