Reef Angel Forum

Im pretty sure its right at least as far as I can tell, It worked for over a year and I didn't change anything in the router after I did the terra term thing. I did change it in the router last night though, I removed it and reinstalled it on that port. It does update every 5 minutes on the portal n...

well I didn't get mine working so don't thank me just yet lol

Did you try the first suggestions he responded to me with? From what I understand is the servers were changed and the wifi attachment needs to know where to look now.

Also I just connected through the app while im on my home network. I just changed the ip address in the app to 192.168.1.2 port 2000 and it works fine.

I just checked it on the multimeter cable it seems ok.

Yes i did and it still is. The thing thats odd is it hadent updated since december 23 or so on the portal but it shows it updated yesterday when i was running the terra term

Yep, It seems to be connecting to the internet fine, I logged into my router and it shows it on the wifi, but I just cant communicate with it through the portal or my app.

So I gave it a shot and its still a no go, but now its worse because I cant connect to it at all anymore. It is connected to the internet though. this is the response from terra term $$$ ERR: ?-Cmd <4.00> get e wifly-GSX Ver 4.00.1, Apr 19 2013 11:48:31 on RN-131 Beacon=102 Reboot=0 IF=UP DHCP=ON IP...

Ill give it a shot thanks!

My reef angel is still functioning properly and I can connect to it through the portal and ios app, but it has stopped recording any graph data or sending me email notifications. In the portal and the app when I try to graph anything it just says no data to display. I havent changed or touched anyth...

I do have the original probe with the extension cable hiding somewhere. it always read about about .2 off from the other but i guess if its an over heat only probe ican take that into account. i assume i just set t1 or t2 to their specified ports depending on which one is wich when i plug them in. I...

Ahh... I think it is the time difference. I'm on PDT, so 9:41 is showing to me as 6:41. If I decrease 3 hours, I see no temp readings from 2:55 to 6:41, which is what you are mentioning. So, I was looking at the steep increase showing in your side starting at 11:06. I'm assuming this is not the rig...

Ok here is the code anyways. I do have the portal alarms set up, but Like you said I need to tighten them up some I had my over heat set for a drastic situation. I just was putting to much faith in one feature without a backup which was dumb on my part. Any reason why the unit would not get a signal...

#include <ReefAngel_Features.h> #include <Globals.h> #include <RA_Wifi.h> #include < Wire .h> #include < OneWire .h> #include <Time.h> #include <DS1307RTC.h> #include <InternalEEPROM.h> #include <RA_NokiaLCD.h> #include <RA_ATO.h> #include <RA_Joystick.h> #include < LED .h> #include <RA_TempSensor....

I am getting nothing either for chrome or IE, In the graph link, in my app also the time scale on the bottom jumps from 5:55 to 9:40. and there is a two degree swing. Well from what I have checked manually with a thermometer and what I can see on the app is the tank did go up 2 degrees over its norm...

Sorry I cant get the code right now as I am at work but I will when I get home. I understand the thermostat as a backup I was just confused why that would matter but as I didnt explain to you how I was using the system I understand now. I do have my overheats sets but I will tighten up the constrain...

Let me start with Thank you for the reply, Rimai: I did not see if the heater was on during the this time I only noticed because the Cooling fan kicked on at 9:40ish and it never turns on but at that point the heater was off. It must have been on though since the ambient temperature was 72, no light...

Im not sure why and luckily i was home but the heater relay turned on and didnt turn off for about 3 hours. The temperature in the tank went up a couple degrees so hopefully everything survives This unit has been running over a year and i havent had any other issues or changed the code. The odd thin...

So I found I can still activate the pumps with a 14v laptop power supply, Is this going to damage anything if I run it continually ?

I am getting the same issues as all of the above. with a 6s and ios 9.0.2

Thanks for the reply. I have a couple of rw-4's and they are too powerful in my tank to run over 40-50% power, but I would still like to run the programs that are in the wizard. So if I use the programs and have a max value of say 40% there is very little change its almost like im running them on co...

I tried to plug in my 12v instead of my 24v power supplies into the battery backup (powerhead input power) to cut the power of the pumps some (no battery or charger attached yet), and the pumps didnt run. Since the 24v works fine and a 12v doesn't, am I correct in assuming that the way it works is w...

Ok one more thing I dont know much about circuits so forgive me if this sounds dumb. I tried to plug in my 12v power supplys into the unit to cut the power of the pumps some (no battery or charger attached yet), and the pumps didnt run. Since the 24v works and the 12v doesn't, am I correct in assumi...

Worked like a charm! Thank you.

Awesome. Yeah im pretty good, shouldnt be a problem. I will give iT a shot. Is that all that is required?

So if that one is out is there a way to do it through the relay box?

Just got home to check but Yes it does.

I just received my battery backup controller last night which I couldn't get to work, and I now realized when I ordered my RA back in aug 2013 I asked for my relay box with outputs to be 0-5v pwm. I also ordered a dimming expansion at the same time. So my question is, Im not sure if that dimming exp...

So my Wifi has been running fine then randomly after a few days I noticed my portal wasnt updating and all the lights on the wifi attachment were blinking quickly. I unplugged it and when i plugged it back in it ran fine for about 2 minutes then back to all blinking. I since had it unplugged a few d...