Reef Angel Forum

Makes sense. Mine is glitchie sometimes too. be fine then have to reset ato once then good sometimes gotta reset it multiple times o well I always get a email so not like ill for get with 1hr reminder lol

been trying to find out y mt ato times out even when increasing the time but i just relized the ato cycle is atoextendedtimeout should that be like that or just atotimeout or do i just need to adjust both if the atoextendedtimeout need to be higher the the atotimeout?

New coding help I need add a few things need dc pump mode for a adjustable amount of hours maybe time can be different but would like it to switch from sine , and short pulse , and when leaving feed mode to be in nutrient expor mode for a adjustable about of time and to have a max setting for adjust...

First of all the Jwabo pump are 0=10v not 0-5v. Secondly I haven't seen one go below 25%. My WP 40 has a lower limit of 30% and my WP 25 had a lower limit of 25% lnevo helped me with a lot of my coding, but I don't think I have a lower limit set. I think I get set it so the variation would not go b...

First of all the Jwabo pump are 0=10v not 0-5v. Secondly I haven't seen one go below 25%. My WP 40 has a lower limit of 30% and my WP 25 had a lower limit of 25% lnevo helped me with a lot of my coding, but I don't think I have a lower limit set. I think I get set it so the variation would not go b...

I got the app to set it lol I missed that . It's working great on 0-5v . The harness they make have voltage dividers in them to drop 0-10v in half to 0-5v is what I got from bunch of diy cables all 0-10v diy treads had risistors in them to be voltage dividers

O I thought that but it was working fine at current setting so wasn't adjustin it but I figured that's what it was and updated code to correct it and still good lol some good to go. TanKS a mil as always Nevo

I seen so things that says 0-5v will work on 0-10v they say but can't exceed 5v. So they put voltage divider circuit in the harness. But it's the expansion itself I probed the breakouts and everything works as it should expect channel 4

Idk If channel 4 worked or not befor a diy jabeo harness but I set jumpers to 5v anolog and only seeing 0.53 volts at 100% undid jumpers and maybe got 0.56v not sure might been the same. I did have a backwards wire on the pump side of the harness the ground and 5v signal was swapped or maybe while t...

Ok made my cable. Now seems like the pumps have no operation under 17% so how do I add a limit to the dc pump code to not allow pwm 4 and 5 (which is 5v anolog with the jumpers) to not fall past 19% bout not sure if it wI'll effect my feeding and wc mode to 0%/off

I updated the code and removed the high line I don't see a effect but it is working so fine with me

seems to work just fine today

O really I haven't seen a issue with it I do think angel is spelled wrong tho lol .I caught that just befor I uploaded.

I think it works perfectly. The other one didn't work cus during the timer hold it didn't hold the ato timeout and would not work after the time out cus the code still thought it was running when the time out stoped it and never got to cycle after timed out. But this new one seems to be perfect.

Ok that is for every 6 hours ato Will cycle one time if float is in need of top off till next 6th hour? Does it as well do the ato time out and stop it from cycling again till ato time out is cleared?(cus I am having issue with time out when it time out it will stop and flag then next time float tog...

It has nothing to do with the timeout memory location. As long as you don't exceed 69 seconds it won't be a problem. If you want to incorporate the memory info, you can replace the 70 with the following InternalMemory.ATOHighExtendedTimeout_read()+10; // 10 seconds more than timeout in portal - to ...

Sweat thanks as always lee. If I write a line like the overheat turn off port code with ato time out would that work? Cus when the float gets toggled again it cycles even tho ato time out flag is on

Ok like this and possibly longer time if (now()%6*SECS_PER_HOUR<70) { ReefAngel.SingleATOLow( Port7 ); // Auto top off } else { ReefAngel.Relay.Off( Port7 ); } and is the ato time out still the same and this is just a new addition and Will not modify with ato timeout memory location or is that one n...

I have updated the refresh to a higher time and switched to home and haven't seen error yet so well see thanks if it goes away lol my phone going off all the time was driving me nuts lol

My time out is 60 seconds so Like this ? Then I replace the original ato line with the above or should there be a * and or % in there ?

ok when you say where it says ATOCodeHere() this is my current code ReefAngel.SingleATOLow( Port7 ); // Auto top off it was like this the one u posted if (now()%6*SECS_PER_HOUR<SECS_PER_HOUR) { AddATOCodeHere(); } else { ReefAngel.Relay.Off(ATO_PORT_HERE); } so it needs to look like this ? if (now()...

I adjusted the time refresh it was on every 5 mins lol it has lessined .
Here is the profile on the app how do I see the hostnames that ur talking about

does it go in the void loop in addition to the already ato code or like this for 60 seconds for every 6 hours #include <ReefAngel_Features.h> #include <Globals.h> #include <RA_Wifi.h> #include <Wire.h> #include <OneWire.h> #include <Time.h> #include <DS1307RTC.h> #include <InternalEEPROM.h> #include...

Still learning I can modify some codes but only values. But what I want to know is I have 1 float running my ato so it always clicks on and of couple times when the water drops a little from my wave makers . So I need to add in to my code to only allow ato to work once every 6 hours. Plus need to ma...

Roberto was working on this. You could graph the value of R (main relay box) or R1 (relay box 1). It may he hard to read though because its the binary value of the relay box status. Looks like it only gives me 1 ready for 2 and it goes from -200 to 0 to 200 scale with some reading of 2 163 and othe...

I get errors all day long is there something I should look at ? Like it will say couple different errors and like when u try to change settings like flip relays on or off or adjust dimming it will error sometimes too. And if I do a couple of things on after another it is worse