Reef Angel Forum

I used to use the following code for one of my water level sensors to control my ATO pump. if ( ReefAngel.WaterLevel.GetLevel(2) <= 54 && ReefAngel.WaterLevel.GetLevel(2) >= 9 ) ReefAngel.Relay.On( TopOff ); if ( ReefAngel.WaterLevel.GetLevel(2) >= 81 || ReefAngel.WaterLevel.GetLevel(2) < 9 ...

Tried it with the Relay expansion box and can toggle the ports from Uapp and Android app (after I put it back together ).

Thank again!

Looks like it's connected now. Thank you. mounted file system *WM: Adding parameter *WM: Cloud Username *WM: Adding parameter *WM: Cloud Password *WM: *WM: AutoConnect *WM: Connecting as wifi client... *WM: Using last saved values, should be faster *WM: Connection result: *WM: 0 *WM: SET AP STA Ente...

Yep, got that part.

Driver installed Solid blue light Output: Failed, rc=-2 try again in 30 seconds Connecting to cloud server... Failed, rc=-2 try again in 30 seconds Connecting to cloud server... Failed, rc=5 try again in 30 seconds Connecting to cloud server... Failed, rc=-2 try again in 30 seconds Connecting to clo...

I do have Arduino IDE installed. With the Cloud expansion connected, I am unable to select the serial port where it is attached. When I go to tools in Arduino IDE, "Serial Port" is a grayed out option. I have tried on the laptop that I use to upload code to the RA* and tried on another des...

It depends on which version of the pump you are trying to use it with. I have a DCP-10000 and have to use the controller that came with the pump. I'm fairly certain the cable works with the DC-XXXX versions. I'm not sure about the DCT-XXXX versions but I don't think so. These are just the return pum...

To verify the cables and box worked, I connected Box 2 to the RA* (through an expansion hub) and the ports toggle off and on via the Uapp and Android App when connected that way.

Box 1 is connected directly to the RA* head unit and ports do toggle with both Uapp and the Android App. Box 2 is connected to the Cloud Wifi hub and show the change on the screens, but the outlets don't come on.

I am using the Uapp. I can see Expansion Box 2 but when I toggle the ports, they don't come on. I have the dip switches in the following positions: 1 - on, 2 - off, 3 - off

I used the cloud wifi attachment 2.0 manual and I can see it on my local network (flashing cyan light) but I haven't figured out how to access modules attached to it; currently having a Relay Expansion Box (configure #2) and a Dimming Expansion Module attached.

That works. Thanks.

The board is a Cloud Wifi Expansion v 1.4

Hey Roberto, I'll open it up when I get home this evening (at work right now) but I want to make sure of the terminology. I don't think I have a cloud wifi 'attachment,' I believe I have a cloud wifi 'hub' to go with my RA*. Also, I didn't upload the code since the initial version above, that the Wi...

I'm starting the initial setup of my Cloud Wifi hub using the Wizard. I'm getting the following error when trying to compile the generated code: --------- Compiling code for RA_CLOUD board Extra Temperature Probes D:\Arduino\libraries\PubSubClient\PubSubClient.cpp:9:21: fatal error: avr/wdt.h: No su...

I did try using two other usb ports on the expansion hub but I think it's all OBE (overcome by events) now. I tried using the new power supply with the older module/probe and it began to work. I calibrated it as well and now showing 35.2 ppt. I then plugged the original power supply back in and it i...

Yep, odd. Green light on both modules; with two different usb cords. When calibrating, the calibration value is '0' with both modules whether in the calibration solution, in tank water, or not in liquid at all. After the calibration, 5.9 showing as salinity.

I have an RA* and the salinity is stuck at 5.9. When first setup, calibrated to 35 ppt, and salt added to the setup, it would show much higher than my refractometer (45 ppt with the refractometer at 35 ppt). On further attempts to calibrate it, it got closer, but not quite there. During one attempt,...

Thanks for the quick reply. NP.

I have a RA* controller I've also added an additional temp probe to my system and found two ways to add it in code. I found this first: ReefAngel.Params.Temp[T4_PROBE]; <--- didn't notice a change And then in this thread: ReefAngel.AddExtraTempProbes(); <--- displays temp 4, 5, & 6 to the LCD an...

Thanks Roberto, both of those methods worked are useful. Is there a way I can assign a static IP address to the controller?

I have a RA Star controller. Using the the built in wired Ethernet, I can browse to the controller, but all I get is "Reef Angel Controller Web Server" and a blank page. What am I doing wrong?

Ooops... just realized I was posting in the wrong forum.

Got it. And thank you again for the excellent customer service!

Feeling kinda dumb here, but I'm not familiar with the input port connector(s) used for ATO and alarm [RA Star].

How do I make a connection to/with them?

Thanks Roberto. That'll work. To drain water, I'll be opening two of these valves simultaneously; both can be on the same power supply. Additionally, for the fill, it'll be a solenoid valve and a pump and I can use the same method. I'm thinking I'll need more than 8 outlets anyway so a Relay Expansi...

New to RA here and I'd like a little advice on how to operate a 12V 3/4" water solenoid valve. I have plumbed my tank to so that I have a (semi) permanent siphon in order to perform no bucket water changes into a deep sink in an adjacent room from my setup. I have purchased a Reef Angel Star co...

Gosh, I wish I'd seen this post yesterday as I just ordered the Jebao cable in hopes I could control my DCP-10000 return pump.