My code - now with RAnet
Re: My code - water level ATO help needed
Does the red light turns on immediately or it turns on after 60 seconds?
Roberto.
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code - water level ATO help needed
ok, so I unplugged RA and plugged back in. no red light. ATO is on auto per portal. water level is at 55 currently, so it should be running but it's not.rimai wrote:Does the red light turns on immediately or it turns on after 60 seconds?
I turn it to on manually, it doesn't shut off when it hits 60 seconds or 58% water level. If I set it back to auto it stays off.
the portal still says water is 55% but RA says 59%
unfortunately, I couldn't reproduce the red light issue now.
Re: My code - water level ATO help needed
It won't turn on until it reaches 52%. That's what you set it at.
It turns on at 52% and off at 58%.
So, when the level does get to 52, you have 60 seconds to pump water until it hits 58% or the timeout will happen and disable the ATO. This is a safety feature to prevent overflow. That's when the red light goes on, indicating an ATO timeout.
So, I think you are using too high of a range and too low of a timeout. Can you pump that much water in 60 seconds?
It will never shut off if you turn on manually. That's what we call override. You are forcing an on position situation no matter what the controller thinks it should be.
It turns on at 52% and off at 58%.
So, when the level does get to 52, you have 60 seconds to pump water until it hits 58% or the timeout will happen and disable the ATO. This is a safety feature to prevent overflow. That's when the red light goes on, indicating an ATO timeout.
So, I think you are using too high of a range and too low of a timeout. Can you pump that much water in 60 seconds?
It will never shut off if you turn on manually. That's what we call override. You are forcing an on position situation no matter what the controller thinks it should be.
Roberto.
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code - water level ATO help needed
I found this is someone else's thread http://forum.reefangel.com/viewtopic.ph ... ion#p14563rimai wrote:It won't turn on until it reaches 52%. That's what you set it at.
It turns on at 52% and off at 58%.
So, when the level does get to 52, you have 60 seconds to pump water until it hits 58% or the timeout will happen and disable the ATO. This is a safety feature to prevent overflow. That's when the red light goes on, indicating an ATO timeout.
So, I think you are using too high of a range and too low of a timeout. Can you pump that much water in 60 seconds?
It will never shut off if you turn on manually. That's what we call override. You are forcing an on position situation no matter what the controller thinks it should be.
Code: Select all
// If water level less than 58, turn on auto top off relay; else, keep it off
if (ReefAngel.WaterLevel.GetLevel()<58) ReefAngel.Relay.On(Port7);
else ReefAngel.Relay.Off(Port7);
or does it still need a timeout, just in case?
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code - water level ATO help needed
Code: Select all
#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <ReefAngel.h>
/*
#define Heater 1
#define Return 2
#define Skimmer 3
#define Vortech1 5
#define Vortech2 6
#define ATO 7
*/
////// Place global variable code below here
byte vtechmode;
////// Place global variable code above here
void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = Port4Bit | Port5Bit | Port6Bit;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = Port7Bit | Port4Bit | Port5Bit | Port6Bit;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = 0;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = Port1Bit | Port2Bit | Port7Bit | Port4Bit | Port5Bit | Port6Bit;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;
// Ports that are always on
ReefAngel.Relay.On( Port2 );
////// Place additional initialization code below here
// Hardcode PH calibrations
ReefAngel.PHMin=576; // PH7.0
ReefAngel.PHMax=842; // PH10.0
ReefAngel.SalMax=3000; // 35ppt
////// Place additional initialization code above here
}
void loop()
{
ReefAngel.StandardHeater( Port1,796,802 );
// ReefAngel.WaterLevelATO( Port7,60,52,58 ); // 60 seconds timeout, turn on at 52% and turn off at 58%
// If water level less than 58, turn on auto top off relay; else, keep it off
if (ReefAngel.WaterLevel.GetLevel()<58) ReefAngel.Relay.On(Port7);
else ReefAngel.Relay.Off(Port7);
ReefAngel.PWM.Channel1PWMParabola();
ReefAngel.PWM.Channel2PWMParabola();
ReefAngel.PWM.Channel3PWMParabola();
ReefAngel.PWM.Channel4PWMSlope();
ReefAngel.RF.UseMemory = true;
if ( ReefAngel.LowATO.IsActive())
{
ReefAngel.Relay.On(Port2);
}
else
{
ReefAngel.Relay.Off(Port2);
}
if (hour() <= 8 && hour() >= 20)
{
ReefAngel.PWM.SetChannel( 0, MoonPhase() );
ReefAngel.RF.UseMemory=false;
ReefAngel.RF.SetMode(Night,15,0);
vtechmode = 9;
}
else
{
ReefAngel.RF.UseMemory=true;
vtechmode = InternalMemory.RFMode_read();
ReefAngel.PWM.SetChannel( 0, MoonPhase(0) );
}
// This should always be the last line
ReefAngel.Portal( "bencollinz" );
ReefAngel.ShowInterface();
}
void DrawCustomMain()
{
char text[7];
// Date and Time
ReefAngel.LCD.DrawDate( 6, 2 );
ReefAngel.LCD.Clear(COLOR_BLACK, 1, 11, 132, 11);
pingSerial();
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 6, 90, "--------------------");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 6, 126, "--------------------");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 2, 93, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 2, 103, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 2, 113, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 2, 123, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 126, 93, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 126, 103, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 126, 113, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 126, 123, "|");
ReefAngel.LCD.DrawText(0,255,10,30,"Temp");
ConvertNumToString(text, ReefAngel.Params.[T1_PROBE], 10);
ReefAngel.LCD.DrawLargeText(COLOR_INDIANRED, 255, 10, 40, text, Num8x8);
pingSerial();
ReefAngel.LCD.DrawText(0,255,100,30,"pH");
ConvertNumToString(text, ReefAngel.Params.PH, 100);
ReefAngel.LCD.DrawLargeText(COLOR_PLUM, 255, 85, 40, text, Num8x8);
pingSerial();
ReefAngel.LCD.DrawText(0,255,43,48,"Salinity");
ConvertNumToString(text, ReefAngel.Params.Salinity, 100);
ReefAngel.LCD.DrawLargeText(COLOR_LIMEGREEN, 255, 49, 58, text, Num8x8);
pingSerial();
// Main Relay Box
byte TempRelay = ReefAngel.Relay.RelayData;
TempRelay &= ReefAngel.Relay.RelayMaskOff;
TempRelay |= ReefAngel.Relay.RelayMaskOn;
ReefAngel.LCD.DrawOutletBox( 12, 77, TempRelay );
pingSerial();
// water level
ReefAngel.LCD.DrawText(0,255,8,68,"WL:");
ReefAngel.LCD.DrawText( COLOR_CORNFLOWERBLUE, 40, 68, 10, ReefAngel.WaterLevel.GetLevel() );
pingSerial();
}
void DrawCustomGraph()
{
}
and I can't get water level to display on screen, what's wrong there?
Re: My code - water level ATO help needed
Your coordinates are wrong.
It's printing at coordinates x=68 and y=10.
I think you what you want is this:
The code you are using does just that. It will turn on whenever the level goes below 58. There is no hysteresis.
If you want hysteresis, you need to use the previous function you were using before. The one you commented out.
It's printing at coordinates x=68 and y=10.
I think you what you want is this:
Code: Select all
ReefAngel.LCD.DrawText( COLOR_CORNFLOWERBLUE,255, 40, 68, ReefAngel.WaterLevel.GetLevel() );
If you want hysteresis, you need to use the previous function you were using before. The one you commented out.
Roberto.
Re: My code - water level ATO help needed
It sounds like from what you want is to use the WaterLevelATO and just increase your timeout... or reduce the high/low difference...
I would suggest something like this.. 3 minutes instead of 1.
Another thing that will help to put the numbers in a better perspective is.. How long does it take to fill your sump from 52 to 58. That plus a few seconds is what you want your timeout to be.
The code you have everytime it drops to 57 it will turn on till 58 and sometimes the reported level varies from the sensor, so thats why you're seeing on / off / on / off
The other choice is making the numbers smaller. If you want it on at 52%, then leave than and reduce the 58 to something you can get to within 60 seconds.. Say 54%
I would suggest something like this.. 3 minutes instead of 1.
Code: Select all
ReefAngel.WaterLevelATO( Port7,180,52,58 ); // 180 seconds timeout, turn on at 52% and turn off at 58%
The code you have everytime it drops to 57 it will turn on till 58 and sometimes the reported level varies from the sensor, so thats why you're seeing on / off / on / off
The other choice is making the numbers smaller. If you want it on at 52%, then leave than and reduce the 58 to something you can get to within 60 seconds.. Say 54%
Code: Select all
ReefAngel.WaterLevelATO( Port7,60,52,54 ); // 60 seconds timeout, turn on at 52% and turn off at 54%
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code - water level ATO help needed
now I get this...
Code: Select all
#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <ReefAngel.h>
/*
#define Heater 1
#define Return 2
#define Skimmer 3
#define Vortech1 5
#define Vortech2 6
#define ATO 7
*/
////// Place global variable code below here
byte vtechmode;
////// Place global variable code above here
void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = Port4Bit | Port5Bit | Port6Bit;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = Port7Bit | Port4Bit | Port5Bit | Port6Bit;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = 0;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = Port1Bit | Port2Bit | Port7Bit | Port4Bit | Port5Bit | Port6Bit;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;
// Ports that are always on
ReefAngel.Relay.On( Port2 );
////// Place additional initialization code below here
// Hardcode PH calibrations
ReefAngel.PHMin=576; // PH7.0
ReefAngel.PHMax=842; // PH10.0
ReefAngel.SalMax=3000; // 35ppt
////// Place additional initialization code above here
}
void loop()
{
ReefAngel.StandardHeater( Port1,796,802 );
ReefAngel.WaterLevelATO( Port7,600,55,58 ); // 60 seconds timeout, turn on at 55% and turn off at 58%
// If water level less than 58, turn on auto top off relay; else, keep it off
// if (ReefAngel.WaterLevel.GetLevel()<58) ReefAngel.Relay.On(Port7);
// else ReefAngel.Relay.Off(Port7);
ReefAngel.PWM.SetChannel( 0, MoonPhase() );
ReefAngel.PWM.Channel1PWMParabola();
ReefAngel.PWM.Channel2PWMParabola();
ReefAngel.PWM.Channel3PWMParabola();
ReefAngel.PWM.Channel4PWMSlope();
if ( ReefAngel.LowATO.IsActive())
{
ReefAngel.Relay.On(Port2);
}
else
{
ReefAngel.Relay.Off(Port2);
}
if (hour() <= 8 && hour() >= 20)
{
ReefAngel.RF.UseMemory=false;
ReefAngel.RF.SetMode(Night,15,0);
vtechmode = 9;
}
else
{
ReefAngel.RF.UseMemory=true;
vtechmode = InternalMemory.RFMode_read();
}
// This should always be the last line
ReefAngel.Portal( "bencollinz" );
ReefAngel.ShowInterface();
}
void DrawCustomMain()
{
char text[7];
// Date and Time
ReefAngel.LCD.DrawDate( 6, 2 );
ReefAngel.LCD.Clear(COLOR_BLACK, 1, 11, 132, 11);
pingSerial();
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 6, 90, "--------------------");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 6, 126, "--------------------");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 2, 93, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 2, 103, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 2, 113, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 2, 123, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 126, 93, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 126, 103, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 126, 113, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 126, 123, "|");
ReefAngel.LCD.DrawText(0,255,10,30,"Temp");
ConvertNumToString(text, ReefAngel.Params.[T1_PROBE], 10);
ReefAngel.LCD.DrawLargeText(COLOR_INDIANRED, 255, 10, 40, text, Num8x8);
pingSerial();
ReefAngel.LCD.DrawText(0,255,100,30,"pH");
ConvertNumToString(text, ReefAngel.Params.PH, 100);
ReefAngel.LCD.DrawLargeText(COLOR_PLUM, 255, 85, 40, text, Num8x8);
pingSerial();
ReefAngel.LCD.DrawText(0,255,43,48,"Salinity");
ConvertNumToString(text, ReefAngel.Params.Salinity, 10);
ReefAngel.LCD.DrawLargeText(COLOR_LIMEGREEN, 255, 49, 58, text, Num8x8);
pingSerial();
// Main Relay Box
byte TempRelay = ReefAngel.Relay.RelayData;
TempRelay &= ReefAngel.Relay.RelayMaskOff;
TempRelay |= ReefAngel.Relay.RelayMaskOn;
ReefAngel.LCD.DrawOutletBox( 12, 77, TempRelay );
pingSerial();
// water level
ReefAngel.LCD.DrawText(0,255,8,68,"WL:");
ReefAngel.LCD.DrawText( COLOR_CORNFLOWERBLUE,255, 40, 68, ReefAngel.WaterLevel.GetLevel() );
pingSerial();
}
void DrawCustomGraph()
{
}
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code - water level ATO help needed
Thank you, that worked!rimai wrote:Your coordinates are wrong.
It's printing at coordinates x=68 and y=10.
I think you what you want is this:.Code: Select all
ReefAngel.LCD.DrawText( COLOR_CORNFLOWERBLUE,255, 40, 68, ReefAngel.WaterLevel.GetLevel() );
Re: My code - water level ATO help needed
I think you already figured out, but just for records...
Your reference to T1 was wrong....
It should be this:
Your reference to T1 was wrong....
It should be this:
Code: Select all
ConvertNumToString(text, ReefAngel.Params.Temp[T1_PROBE], 10);
Roberto.
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code - water level ATO help needed
yessir! everything is working so far, have to wait and see about the ATO changes.rimai wrote:I think you already figured out, but just for records...
Your reference to T1 was wrong....
It should be this:Code: Select all
ConvertNumToString(text, ReefAngel.Params.Temp[T1_PROBE], 10);
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code
Code: Select all
if ( ReefAngel.LowATO.IsActive())
{
ReefAngel.Relay.On(Port2);
}
else
{
ReefAngel.Relay.Off(Port2);
Re: My code
Use the SingleATOLow function
Code: Select all
SingleATOLow(Port2);
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code
maybe I'm misunderstanding, I changed it to this:lnevo wrote:Use the SingleATOLow function
Code: Select all
SingleATOLow(Port2);
Code: Select all
ReefAngel.SingleATOLow(Port2);
My code
Did you change that whole section of code? It should go off when the switch is inactive. You may have the switch upside down. Which way is it facing?
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code
the wires are facing up. i removedlnevo wrote:Did you change that whole section of code? It should go off when the switch is inactive. You may have the switch upside down. Which way is it facing?
Code: Select all
if ( ReefAngel.LowATO.IsActive())
{
ReefAngel.Relay.On(Port2);
}
else
{
ReefAngel.Relay.Off(Port2);
Code: Select all
ReefAngel.SingleATOLow(Port2);
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code - water level ATO help needed
so i changed it back to this formatlnevo wrote:It sounds like from what you want is to use the WaterLevelATO and just increase your timeout... or reduce the high/low difference...
I would suggest something like this.. 3 minutes instead of 1.Another thing that will help to put the numbers in a better perspective is.. How long does it take to fill your sump from 52 to 58. That plus a few seconds is what you want your timeout to be.Code: Select all
ReefAngel.WaterLevelATO( Port7,180,52,58 ); // 180 seconds timeout, turn on at 52% and turn off at 58%
The code you have everytime it drops to 57 it will turn on till 58 and sometimes the reported level varies from the sensor, so thats why you're seeing on / off / on / off
The other choice is making the numbers smaller. If you want it on at 52%, then leave than and reduce the 58 to something you can get to within 60 seconds.. Say 54%Code: Select all
ReefAngel.WaterLevelATO( Port7,60,52,54 ); // 60 seconds timeout, turn on at 52% and turn off at 54%
Code: Select all
ReefAngel.WaterLevelATO( Port7,60,52,54 );
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code
the red light was on, I chose clear ATO it started and wouldn't stop. the red light came on again, I cleared again, it still wouldn't turn off. it's now at 61% again. I had to turn off manually.rimai wrote:Are you sure it isn't timed out already?
Just to be sure, can you clear ATO?
current code:
Code: Select all
#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <ReefAngel.h>
/*
#define Heater 1
#define Return 2
#define Skimmer 3
#define Vortech1 5
#define Vortech2 6
#define ATO 7
*/
////// Place global variable code below here
byte vtechmode;
////// Place global variable code above here
void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = Port4Bit | Port5Bit | Port6Bit;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = Port7Bit | Port4Bit | Port5Bit | Port6Bit;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = 0;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = Port1Bit | Port2Bit | Port7Bit | Port4Bit | Port5Bit | Port6Bit;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;
// Ports that are always on
ReefAngel.Relay.On( Port2 );
////// Place additional initialization code below here
// Hardcode calibrations
ReefAngel.PHMin=576; // PH7.0
ReefAngel.PHMax=842; // PH10.0
ReefAngel.SalMax=3000; // 35ppt
////// Place additional initialization code above here
}
void loop()
{
ReefAngel.StandardHeater( Port1,796,802 );
ReefAngel.WaterLevelATO( Port7,600,58,60 );
// If water level less than 58, turn on auto top off relay; else, keep it off
// if (ReefAngel.WaterLevel.GetLevel()<58) ReefAngel.Relay.On(Port7);
// else ReefAngel.Relay.Off(Port7);
ReefAngel.PWM.SetChannel( 0, MoonPhase() );
ReefAngel.PWM.Channel1PWMParabola();
ReefAngel.PWM.Channel2PWMParabola();
ReefAngel.PWM.Channel3PWMParabola();
ReefAngel.PWM.Channel4PWMSlope();
// ReefAngel.SingleATOLow(Port2);
if ( ReefAngel.LowATO.IsActive())
{
ReefAngel.Relay.On(Port2);
}
else
{
ReefAngel.Relay.Off(Port2);
if (hour() <= 8 && hour() >= 20)
{
ReefAngel.RF.UseMemory=false;
ReefAngel.RF.SetMode(Night,15,0);
vtechmode = 9;
}
else
{
ReefAngel.RF.UseMemory=true;
vtechmode = InternalMemory.RFMode_read();
}
// This should always be the last line
ReefAngel.Portal( "bencollinz" );
ReefAngel.ShowInterface();
}
void DrawCustomMain()
{
char text[7];
// Date and Time
ReefAngel.LCD.DrawDate( 6, 2 );
ReefAngel.LCD.Clear(COLOR_BLACK, 1, 11, 132, 11);
pingSerial();
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 6, 90, "--------------------");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 6, 126, "--------------------");
for (byte Left=93; Left < 133; Left+=10)
{
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 2, Left, "|");
ReefAngel.LCD.DrawText(COLOR_TOMATO,255, 126, Left, "|");
}
ReefAngel.LCD.DrawText(0,255,18,12,"EcoSmart Vortech");
ReefAngel.LCD.Clear(255, 1, 19, 128, 29);
if (vtechmode == 0) ReefAngel.LCD.DrawLargeText(COLOR_LIMEGREEN,255,35,21,"Constant");
else if(vtechmode == 1) ReefAngel.LCD.DrawLargeText(COLOR_GOLD,255,42,21,"Lagoon");
else if (vtechmode == 2) ReefAngel.LCD.DrawLargeText(COLOR_GOLD,255,25,21,"Reef Crest");
else if (vtechmode == 3) ReefAngel.LCD.DrawLargeText(COLOR_CORNFLOWERBLUE,255,22,21,"Short Pulse");
else if (vtechmode == 4) ReefAngel.LCD.DrawLargeText(COLOR_PINK,255,25,21,"Long Pulse");
else if (vtechmode == 5) ReefAngel.LCD.DrawLargeText(COLOR_MAGENTA,255,8,21,"Nutrient Trnsp.");
else if (vtechmode == 6) ReefAngel.LCD.DrawLargeText(COLOR_MAGENTA,255,23,21,"Tidal Swell");
else if (vtechmode == 9) ReefAngel.LCD.DrawLargeText(COLOR_WHITE,0,45,21,"Night");
ReefAngel.LCD.DrawText(0,255,10,30,"Temp");
ConvertNumToString(text, ReefAngel.Params.Temp[T1_PROBE], 10);
ReefAngel.LCD.DrawLargeText(COLOR_INDIANRED, 255, 10, 40, text, Num8x8);
pingSerial();
ReefAngel.LCD.DrawText(0,255,100,30,"pH");
ConvertNumToString(text, ReefAngel.Params.PH, 100);
ReefAngel.LCD.DrawLargeText(COLOR_PLUM, 255, 85, 40, text, Num8x8);
pingSerial();
ReefAngel.LCD.DrawText(0,255,43,48,"Salinity");
ConvertNumToString(text, ReefAngel.Params.Salinity, 10);
ReefAngel.LCD.DrawLargeText(COLOR_LIMEGREEN, 255, 49, 58, text, Num8x8);
pingSerial();
// Main Relay Box
byte TempRelay = ReefAngel.Relay.RelayData;
TempRelay &= ReefAngel.Relay.RelayMaskOff;
TempRelay |= ReefAngel.Relay.RelayMaskOn;
ReefAngel.LCD.DrawOutletBox( 12, 77, TempRelay );
pingSerial();
// water level
ReefAngel.LCD.DrawText(0,255,8,68,"WL:");
ReefAngel.LCD.DrawText( COLOR_CORNFLOWERBLUE,255, 40, 68, ReefAngel.WaterLevel.GetLevel() );
pingSerial();
}
void DrawCustomGraph()
{
}
Re: My code
Are you sure you uploaded this code?
It says timeout is 600 seconds. Was your ATO pump on for 600 seconds before it turned the red led again?
It says timeout is 600 seconds. Was your ATO pump on for 600 seconds before it turned the red led again?
Roberto.
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code
rimai wrote:Are you sure you uploaded this code?
It says timeout is 600 seconds. Was your ATO pump on for 600 seconds before it turned the red led again?
yes, that is the current code.
the red light comes on after 10 mins every time I 'clear ATO' from menu, regardless of the port running or not.
The port did turn itself off at the proper % finally, though.
Re: My code
So, you are getting ato timeout even when the port is supposed to be off?
You are not overriding it off, are you?
If you do, it would definitely timeout.
You are not overriding it off, are you?
If you do, it would definitely timeout.
Roberto.
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code
so, for example, right now, the red light is on. i'll 'clear ato', the water is at 56%, so the port turned on for ATO, the red light came back on ~1-2 mins, i 'clear ato' (the port still on all the while), the port shuts off at 60%.rimai wrote:So, you are getting ato timeout even when the port is supposed to be off?
You are not overriding it off, are you?
If you do, it would definitely timeout.
it's on auto via portal or reboot, not changing to off.
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code
and now the red light is on again. ~10 mins after I last pressed 'clear ato'
cleared it again, got it ~2 mins later
cleared it again, got it ~2 mins later
Re: My code
I think you found a bug
Can you disconnect the ATO Low float switch and see if the problem is fixed?
Can you disconnect the ATO Low float switch and see if the problem is fixed?
Roberto.
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code
I unplugged that, rebooted RA, let it sit for 20 mins and now my return pump port 2 just shut off.rimai wrote:I think you found a bug
Can you disconnect the ATO Low float switch and see if the problem is fixed?
but that was also the first time i set port 2 to auto instead of on.
-
- Posts: 151
- Joined: Wed Mar 13, 2013 5:36 pm
Re: My code
the ATO pump went on and off just as it should without the float switch! and no red light to clear.
Re: My code
Yeah, just what thought.
The libraries code is sharing the part of the code with the low float switch.
I'll have to update it.
Should be fixed in the next update.
In the mean time, you can use the high ato port for your return.
The libraries code is sharing the part of the code with the low float switch.
I'll have to update it.
Should be fixed in the next update.
In the mean time, you can use the high ato port for your return.
Roberto.