Page 1 of 1

Expansion Reboots

Posted: Mon Aug 08, 2016 12:44 pm
by projectx
When I put the system into feeding mode or water change mode my expansion relay reboots.
I recent installed the RA + board, but have never had 2 expansions on this unit.

Any thoughts?

here is my code

#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <DCPump.h>
#include <PAR.h>
#include <ReefAngel.h>

////// Place global variable code below here


////// Place global variable code above here


void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
ReefAngel.Use2014Screen(); // Let's use 2014 Screen
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = Port1Bit | Port2Bit | Port5Bit | Port7Bit;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = Port1Bit | Port2Bit | Port4Bit | Port5Bit | Port6Bit | Port7Bit;
ReefAngel.WaterChangePortsE[0] = Port7Bit | Port8Bit;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = 0;
ReefAngel.LightsOnPortsE[0] = 0;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = Port4Bit | Port6Bit;
ReefAngel.OverheatShutoffPortsE[0] = Port1Bit;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;


// Ports that are always on
ReefAngel.Relay.On( Port1 );
ReefAngel.Relay.On( Port2 );
ReefAngel.Relay.On( Port5 );
ReefAngel.Relay.On( Port7 );
ReefAngel.Relay.On( Box1_Port1 );
ReefAngel.Relay.On( Box1_Port2 );
ReefAngel.Relay.On( Box1_Port5 );
ReefAngel.Relay.On( Box1_Port6 );

////// Place additional initialization code below here
ReefAngel.CustomLabels[0]="Return";
ReefAngel.CustomLabels[1]="Skimmer";
ReefAngel.CustomLabels[2]="";
ReefAngel.CustomLabels[3]="SumpHeater";
ReefAngel.CustomLabels[4]="LeftVortech";
ReefAngel.CustomLabels[5]="TankHeater";
ReefAngel.CustomLabels[6]="RightVortech";
ReefAngel.CustomLabels[7]="";
ReefAngel.CustomLabels[8]="Radion";
ReefAngel.CustomLabels[9]="StndLight";
ReefAngel.CustomLabels[10]="";
ReefAngel.CustomLabels[11]="FugeLight";
ReefAngel.CustomLabels[12]="";
ReefAngel.CustomLabels[13]="";
ReefAngel.CustomLabels[14]="Dosing1";
ReefAngel.CustomLabels[15]="Dosing2";

////// Place additional initialization code above here
}

void loop()
{
ReefAngel.MoonLights( Box1_Port4 );
ReefAngel.StandardHeater( Port4 );
ReefAngel.StandardHeater( Port6 );
ReefAngel.DosingPumpRepeat1( Box1_Port7 );
ReefAngel.DosingPumpRepeat2( Box1_Port8 );
////// Place your custom code below here


////// Place your custom code above here

// This should always be the last line
ReefAngel.Portal( "XXXXXX" );
ReefAngel.ShowInterface();
}

Re: Expansion Reboots

Posted: Thu Aug 11, 2016 4:11 pm
by projectx
On another note, when the system comes out of water change or feeding the expansion doesnt power cycle

Re: Expansion Reboots

Posted: Sun Aug 28, 2016 7:24 pm
by projectx
So something else that just showed up. If port 1 the return pump port is in the on state and not in auto. the expansion does not reboot.

Any ideas?

Re: Expansion Reboots

Posted: Sun Sep 18, 2016 7:53 pm
by rimai
Can you try removing the custom labels to see if that is affecting anything?

Re: Expansion Reboots

Posted: Sun Sep 18, 2016 8:00 pm
by projectx
Ill give it a shot and see. I know I had an issue with a reboot loop with some of the labels

Re: Expansion Reboots

Posted: Sun Sep 25, 2016 7:09 am
by projectx2
I set all of the labels to blank just "" same thing happens

Sent from my SM-G935V using Tapatalk

Re: Expansion Reboots

Posted: Sun Sep 25, 2016 8:33 am
by rimai
Remove the reference from the code.
Even if it is commented, it is still enabled.
When you are in water change mode, go to a browser within the same network and go to http://ipaddress:2000/r99
Send me the XML data you get back.