I currently have a single float ATO and I want to change it to a dual float ATO. Will this be a problem with the ATO reservoir refill being the basic same ATO type?
I also want to semi automate a water change bin refill. I want to fill a Brute trash can with fresh R/O. Again, I've got it on a 12V water solenoid. I want to be able to manually turn it on then have it fill until it trips a float valve at the top. I also want to put in a low float valve so that it won't fill again if it is already full.
I read somewhere here that the 12 v power controller acts like a relay expansion. I tried adding it in the Wizard, but it only lets you add 2 relays. I currently have 2 relays and the PCE would be a third. What can I do.
Here is my current code.
Code: Select all
#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <DCPump.h>
#include <ReefAngel.h>
////// Place global variable code below here
////// Place global variable code above here
void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
ReefAngel.Use2014Screen(); // Let's use 2014 Screen
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = Port1Bit | Port3Bit | Port5Bit | Port6Bit | Port7Bit | Port8Bit;
ReefAngel.FeedingModePortsE[0] = Port2Bit;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = Port1Bit | Port3Bit | Port5Bit | Port6Bit | Port7Bit | Port8Bit;
ReefAngel.WaterChangePortsE[0] = Port2Bit;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = Port2Bit;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = Port3Bit | Port6Bit | Port7Bit | Port8Bit;
ReefAngel.OverheatShutoffPortsE[0] = Port2Bit;
// Use T3 probe as temperature and overheat functions
ReefAngel.TempProbe = T3_PROBE;
ReefAngel.OverheatProbe = T3_PROBE;
// Set the Overheat temperature setting
InternalMemory.OverheatTemp_write( 805 );
// Ports that are always on
ReefAngel.Relay.On( Port3 );
ReefAngel.Relay.On( Box1_Port2 );
ReefAngel.Relay.On( Box1_Port8 );
////// Place additional initialization code below here
////// Place additional initialization code above here
}
void loop()
{
ReefAngel.SingleATO( true,Port1,120,10 );
ReefAngel.StandardLights( Port2,19,0,7,0 );
ReefAngel.StandardLights( Port5,6,0,22,0 );
ReefAngel.StandardHeater( Port6,780,805 );
ReefAngel.Relay.DelayedOn( Port7,5 );
ReefAngel.Relay.DelayedOn( Port8,3 );
ReefAngel.DosingPumpRepeat( Box1_Port3,0,60,170 );
////// Place your custom code below here
if ((now()%SECS_PER_DAY==28800)) //if it is 8 AM
{ReefAngel.FeedingModeStart();} //START FEEDING MODE
if ((now()%SECS_PER_DAY==64800)) //if it is 6 PM
{ReefAngel.FeedingModeStart();} //START FEEDING MODE
////// Place your custom code above here
// This should always be the last line
ReefAngel.Portal( "Spotted" );
ReefAngel.ShowInterface();
}