#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <DCPump.h>
#include <PAR.h>
#include <ReefAngel.h>
////// Place global variable code below here
////// Place global variable code above here
void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
ReefAngel.AddStandardMenu(); // Add Standard Menu
ReefAngel.Use2014Screen(); // Let's use 2014 Screen
ReefAngel.AddPHExpansion(); // pH Expansion Module
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = Port5Bit;
ReefAngel.FeedingModePortsE[0] = 0;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = Port6Bit;
ReefAngel.WaterChangePortsE[0] = 0;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = Port1Bit | Port2Bit;
ReefAngel.LightsOnPortsE[0] = 0;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = Port1Bit | Port2Bit | Port4Bit;
ReefAngel.OverheatShutoffPortsE[0] = 0;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;
// Set the Overheat temperature setting
InternalMemory.OverheatTemp_write( 800 );
// Ports that are always on
ReefAngel.Relay.On( Port5 );
ReefAngel.Relay.On( Port6 );
ReefAngel.Relay.On( Port7 );
ReefAngel.Relay.On( Port8 );
////// Place additional initialization code below here
////// Place additional initialization code above here
}
void loop()
{
ReefAngel.StandardLights( Port1,9,0,21,0 );
ReefAngel.StandardLights( Port2,9,15,21,15 );
ReefAngel.StandardATO( Port3,60 );
ReefAngel.StandardHeater( Port4,779,780 );
////// Place your custom code below here
////// Place your custom code above here
// This should always be the last line
ReefAngel.ShowInterface();
}
wizard code error
-
- Posts: 1
- Joined: Wed May 10, 2017 12:21 pm
wizard code error
when I run through the wizard setup and go to generate the code it gives me errors class reefangleclass has no member named feeding mode portE and does the same for lights on mode, water change mode, overheat shutoff. I have to go in and delete the code for those and then it will compile. why is it doing this?
Re: wizard code error
Because you chose the relay expansion module and never setup any of its ports.
Roberto.
Re: wizard code error
Ok I thought that was the standard relay. Been awhile since I did the initial setup on one. If I delete the reefangel.feedingmodeportsE part of the code it should work fine correct?