- Code: Select all
////// Place global variable code below here
////// Place global variable code above here
void setup()
{
// This must be the first line
InternalMemory.LCDID_write(255); //this line was added when i got a replacement RA+ board
ReefAngel.Init(); //Initialize controller
ReefAngel.Use2014Screen(); // Let's use 2014 Screen
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = Port5Bit | Port6Bit;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = Port3Bit | Port4Bit | Port5Bit | Port6Bit;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = Port1Bit | Port2Bit;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = Port1Bit | Port2Bit | Port3Bit | Port5Bit | Port6Bit;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;
// Feeeding and Water Change mode speed
ReefAngel.DCPump.FeedingSpeed=0;
ReefAngel.DCPump.WaterChangeSpeed=0;
// Ports that are always on
ReefAngel.Relay.On( Port4 );
////// Place additional initialization code below here
////// Place additional initialization code above here
}
void loop()
{
ReefAngel.ActinicLights( Port1 );
ReefAngel.DayLights( Port2 );
ReefAngel.StandardHeater( Port3 );
ReefAngel.Relay.DelayedOn(Port5 );
ReefAngel.DosingPumpRepeat1( Port7 );
ReefAngel.DosingPumpRepeat2( Port8 );
ReefAngel.PWM.DaylightPWMSlope();
ReefAngel.PWM.ActinicPWMSlope();
ReefAngel.DCPump.LowATOChannel = Sync; // WP40
ReefAngel.DCPump.HighATOChannel = AntiSync; // SW-8
ReefAngel.DCPump.AntiSyncOffset = 125;
////// Place your custom code below here
// Wavemaker
if ( ((hour() >= 2) && (hour() < 8)) || ((hour() >= 15) && (hour() < 19)) ) // off from 2am-8am & 3pm-7pm
{
ReefAngel.Relay.Off(Port6);
}
else
{
ReefAngel.WavemakerRandom( Port6, 30, 300 ); // random between 30 and 300 seconds
}
// DC pumps....................................
static int rmode;
static boolean changeMode=true;
// These are the modes we can cycle through. You can add more and even repeat...
byte modes[] = { ReefCrest, Lagoon, TidalSwell, ShortPulse, Sine, Else, Gyre, NutrientTransport };
if (now()%1800==0 || changeMode==true) // Change every 30 mins (1800seconds) or controller reboot
{
rmode=random(100)%sizeof(modes); // Change the mode by picking from our array
changeMode=false;
}
// Set timer when in feeding mode
static unsigned long feeding;
if (ReefAngel.DisplayedMenu==FEEDING_MODE) feeding=now();
// Continue NutrientTranspot Mode for 30 minutes after feeding
if (now()-feeding<1800)
{
ReefAngel.DCPump.UseMemory=false;
ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
ReefAngel.DCPump.Mode=ReefCrest;
ReefAngel.DCPump.Speed=75;
}
// Night/Quiet mode
else if (hour()>=2 && hour()<8 ) // 2am to 8am
{
ReefAngel.DCPump.UseMemory=false;
ReefAngel.DCPump.SetMode( Gyre,40,10 );
}
else if (hour()>=15 && hour()<19) // 3pm and 7pm
{
ReefAngel.DCPump.UseMemory=false;
ReefAngel.DCPump.SetMode( ShortPulse,40,30 );
}
//Storm mode
else if (hour()>=1 && hour()<2) // 1am and 2am
{
ReefAngel.DCPump.UseMemory=false;
ReefAngel.DCPump.SetMode( Else,70,15 );
}
else if (hour()>=11 && hour()<12) // 11am and 12pm
{
ReefAngel.DCPump.UseMemory=false;
ReefAngel.DCPump.SetMode( ReefCrest,80,15 );
}
else if (hour()>=21 && hour()<22) // 9pm and 10pm
{
ReefAngel.DCPump.UseMemory=false;
ReefAngel.DCPump.SetMode( ShortPulse,85,30 );
}
// Custom Mode and nothing else going on
else if (InternalMemory.DCPumpMode_read()==11)
{
ReefAngel.DCPump.UseMemory=false;
ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
ReefAngel.DCPump.Mode=modes[rmode]; // Put the mode to the random mode :)
ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Set speed from portal
} else {
ReefAngel.DCPump.UseMemory=true; // Will reset all values from memory
}
////// Place your custom code above here
Reefology's code
|
|
Hoping someone can help with this. I'd like to add Seasonal changes to my code but can't get it to compile.
where exactly do I input this? |
|
you have to simply copy the entire function and paste it into your INO file, most likely at the end of it. well after the last curly brace of the loop.
Sent from my XT1585 using Tapatalk |
|
Who is online
Users browsing this forum: No registered users and 3 guests