Reef Angel Forum

Posted: **Mon Feb 09, 2015 6:20 am**

What do you want to do with them...if you want to speed one up or slow one down? Which is currently sync/antisync?

Posted: **Mon Feb 09, 2015 7:30 am**

Yup, that's what I want. So do I remove the offset then? Leave it at 100? Or change it to some other figure?

Posted: **Mon Feb 09, 2015 8:56 am**

I gave you two choices...you answered yup. If you want to speed up the antisync channel then make it 125 for a 25% increase. Or make it 75 for a 25% decrease on the one set to antisync

Posted: **Mon Feb 09, 2015 11:55 am**

thanks for the info Lee

i answered "yup" because i'd like to know how to manipulate the fields/data going forward, don't just want to rely on you guys to write code for me (though at times i need you to and certainly do appreciate it). sorry for the confusion

Posted: **Mon Feb 09, 2015 4:05 pm**

No worries just confusing. All good now

Posted: **Wed Nov 02, 2016 8:13 am**

Hi all,

How do I figure out why I can't upload a sketch when it complies just fine?

This is the error message I'm getting:

avrdude: stk500v2_ReceiveMessage(): timeout

Same message I get when try to upload without cable. Can it be a cable issue? It seemed to work yesterday to upload wifitestcode? Sort of...

Posted: **Wed Nov 02, 2016 9:31 am**

Make sure you are connecting the cable correctly on RA. It should be all the way to the right and you should have 2 pins unconnected on the left.

Posted: **Wed Nov 02, 2016 2:03 pm**

Hi Roberto,

Yes thanks, I've uploaded sketches many times so it's definitely not that. Any other ideas?

Posted: **Sat Nov 26, 2016 3:29 pm**

Code: Select all

 // DC pumps
    // To run this code must choose Custom in portal
    static int rmode;
    static boolean changeMode=true;

    // These are the modes we can cycle through. You can add more and even repeat...
    byte modes[] = { NutrientTransport, Sine, ReefCrest, Lagoon, TidalSwell, ShortPulse, Sine, LongPulse, Else, Gyre, NutrientTransport };

    if (now()%1200==0 || changeMode==true) { // Change every 20 (1200seconds) mins or controller reboot
    rmode=random(100)%sizeof(modes); // Change the mode by picking from our array
    changeMode=false;
    }

    // Set timer when in feeding mode
    static unsigned long feeding;
    if (ReefAngel.DisplayedMenu==FEEDING_MODE) feeding=now();
    
    if (now()-feeding<3000) {
    // Continue NutrientTranspot Mode for 45 minutes
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=NutrientTransport;
    } else if (now()%SECS_PER_DAY<37800 || now()%SECS_PER_DAY>=81000) { // 10:30am / 10:30pm
    // Night mode (go to 30%)
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=Gyre;
    ReefAngel.DCPump.Speed=30;
    } else if (InternalMemory.DCPumpMode_read()==11) {
    // Custom Mode and nothing else going on
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=modes[rmode]; // Put the mode to the random mode :)
    ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Set speed from portal
    } else {
    ReefAngel.DCPump.UseMemory=true; // Will reset all values from memory
    }

hi, based on the code above, I don't understand why my pwm channels have been at 0 for the past 45 mins? can someone help me figure out what I've done wrong? thanks

Posted: **Sat Nov 26, 2016 3:29 pm**

Code: Select all

 // DC pumps
    // To run this code must choose Custom in portal
    static int rmode;
    static boolean changeMode=true;

    // These are the modes we can cycle through. You can add more and even repeat...
    byte modes[] = { NutrientTransport, Sine, ReefCrest, Lagoon, TidalSwell, ShortPulse, Sine, LongPulse, Else, Gyre, NutrientTransport };

    if (now()%1200==0 || changeMode==true) { // Change every 20 (1200seconds) mins or controller reboot
    rmode=random(100)%sizeof(modes); // Change the mode by picking from our array
    changeMode=false;
    }

    // Set timer when in feeding mode
    static unsigned long feeding;
    if (ReefAngel.DisplayedMenu==FEEDING_MODE) feeding=now();
    
    if (now()-feeding<3000) {
    // Continue NutrientTranspot Mode for 45 minutes
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=NutrientTransport;
    } else if (now()%SECS_PER_DAY<37800 || now()%SECS_PER_DAY>=81000) { // 10:30am / 10:30pm
    // Night mode (go to 30%)
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=Gyre;
    ReefAngel.DCPump.Speed=30;
    } else if (InternalMemory.DCPumpMode_read()==11) {
    // Custom Mode and nothing else going on
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=modes[rmode]; // Put the mode to the random mode :)
    ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Set speed from portal
    } else {
    ReefAngel.DCPump.UseMemory=true; // Will reset all values from memory
    }

hi, based on the code above, I don't understand why my pwm channels have been at 0 for the past 45 mins? can someone help me figure out what I've done wrong? thanks

Posted: **Sat Nov 26, 2016 3:30 pm**

Code: Select all

 // DC pumps
    // To run this code must choose Custom in portal
    static int rmode;
    static boolean changeMode=true;

    // These are the modes we can cycle through. You can add more and even repeat...
    byte modes[] = { NutrientTransport, Sine, ReefCrest, Lagoon, TidalSwell, ShortPulse, Sine, LongPulse, Else, Gyre, NutrientTransport };

    if (now()%1200==0 || changeMode==true) { // Change every 20 (1200seconds) mins or controller reboot
    rmode=random(100)%sizeof(modes); // Change the mode by picking from our array
    changeMode=false;
    }

    // Set timer when in feeding mode
    static unsigned long feeding;
    if (ReefAngel.DisplayedMenu==FEEDING_MODE) feeding=now();
    
    if (now()-feeding<3000) {
    // Continue NutrientTranspot Mode for 45 minutes
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=NutrientTransport;
    } else if (now()%SECS_PER_DAY<37800 || now()%SECS_PER_DAY>=81000) { // 10:30am / 10:30pm
    // Night mode (go to 30%)
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=Gyre;
    ReefAngel.DCPump.Speed=30;
    } else if (InternalMemory.DCPumpMode_read()==11) {
    // Custom Mode and nothing else going on
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=modes[rmode]; // Put the mode to the random mode :)
    ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Set speed from portal
    } else {
    ReefAngel.DCPump.UseMemory=true; // Will reset all values from memory
    }

hi, based on the code above, I don't understand why my pwm channels have been at 0 for the past 45 mins? can someone help me figure out what I've done wrong? thanks

Posted: **Sat Nov 26, 2016 4:41 pm**

What mode do you see in the screen?

Posted: **Sat Nov 26, 2016 10:04 pm**

not sure which screen you're referring to but in the portal, the internal memory keeps getting reset to 0's for both speed and duration? currently the mode alternates but it was set up in custom??

Posted: **Sat Nov 26, 2016 11:49 pm**

The RA screen. Move the joystick to the right or left.
Or are you using a custom screen?

Posted: **Sun Nov 27, 2016 6:04 pm**

it says normal mode. what is that? don't see it listed in the portal as a mode.

Posted: **Sun Nov 27, 2016 6:51 pm**

Normal?
Are you sure you are in the RF screen?
Can you send a picture?

Posted: **Mon Nov 28, 2016 5:38 pm**

sorry Roberto, the mode is gyre, duration is 15 and speed is 30

Posted: **Mon Nov 28, 2016 7:25 pm**

Which channels did you assign for DCPump?

Posted: **Mon Nov 28, 2016 7:38 pm**

lol, I just logged in to tell you i figured it out...had the actinic channel set to None and of course thought I had the pump wired to daylights :p

thanks Roberto

Posted: **Wed Jan 11, 2017 3:56 pm**

Code: Select all

void setup()
{
    // This must be the first line
    ReefAngel.Init();  //Initialize controller
    ReefAngel.Use2014Screen();  // Let's use 2014 Screen 
    // Ports toggled in Feeding Mode
    ReefAngel.FeedingModePorts = Port5Bit;
    // Ports toggled in Water Change Mode
    ReefAngel.WaterChangePorts = Port3Bit | Port4Bit | Port5Bit;
    // Ports toggled when Lights On / Off menu entry selected
    ReefAngel.LightsOnPorts = Port1Bit | Port2Bit;
    // Ports turned off when Overheat temperature exceeded
    ReefAngel.OverheatShutoffPorts = Port1Bit | Port2Bit | Port3Bit | Port4Bit | Port5Bit | Port7Bit;
    // Use T1 probe as temperature and overheat functions
    ReefAngel.TempProbe = T1_PROBE;
    ReefAngel.OverheatProbe = T1_PROBE;

    // Feeeding and Water Change mode speed
    ReefAngel.DCPump.FeedingSpeed=0;
    ReefAngel.DCPump.WaterChangeSpeed=0;
    
  

    // Ports that are always on
    ReefAngel.Relay.On( Port4 );

    ////// Place additional initialization code below here
    

    ////// Place additional initialization code above here
}

void loop()
{
    ReefAngel.ActinicLights( Port1 );
    ReefAngel.DayLights( Port2 );
    ReefAngel.StandardHeater( Port3 );
    ReefAngel.StandardLights( Port5, 19,0,7,0);
    ReefAngel.DosingPumpRepeat1( Port6 );
    ReefAngel.DosingPumpRepeat2( Port7 );
    ReefAngel.DosingPumpRepeat3( Port8 );
    ReefAngel.PWM.DaylightPWMParabola();
    ReefAngel.PWM.ActinicPWMParabola();
    ReefAngel.DCPump.LowATOChannel = Sync; // WP40 
    ReefAngel.DCPump.HighATOChannel = AntiSync; // SW 8 
    ReefAngel.DCPump.AntiSyncOffset=125;
    
    ////// Place your custom code below here
    
    // DC pumps
    // To run this code must choose Custom in portal
    static int rmode;
    static boolean changeMode=true;

    // These are the modes we can cycle through. You can add more and even repeat...
    byte modes[] = { ReefCrest, Lagoon, TidalSwell, ShortPulse, Sine, LongPulse, Else, Gyre, NutrientTransport };

    if (now()%3600==0 || changeMode==true) { // Change every 60 mins (3600seconds) or controller reboot
    rmode=random(100)%sizeof(modes); // Change the mode by picking from our array
    changeMode=false;
    }

    // Set timer when in feeding mode
    static unsigned long feeding;
    if (ReefAngel.DisplayedMenu==FEEDING_MODE) feeding=now();
    // Continue NutrientTranspot Mode for 30 minutes after feeding
    if (now()-feeding<1800) {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=NutrientTransport;
    ReefAngel.DCPump.Speed=80;
    // Night mode (go to 30%)
    } else if (now()%SECS_PER_DAY>25200 && now()%SECS_PER_DAY<=68400) { // 7am to 7pm
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=Gyre;
    ReefAngel.DCPump.Speed=30;
    } else if (InternalMemory.DCPumpMode_read()==11) {
    // Custom Mode and nothing else going on
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=modes[rmode]; // Put the mode to the random mode :)
    ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Set speed from portal
    } else {
    ReefAngel.DCPump.UseMemory=true; // Will reset all values from memory
    }

Can someone here please tell me why my Jebao wavemaker pump is running full throttle constantly on the ATO high? the ATO low is working great. in fact I made an adaptor to run both pumps on my ATO low and they're working but I'd really like to get the antisync working. The code I'm using in the meantime is below.

thanks

Code: Select all


void setup()
{
    // This must be the first line
    ReefAngel.Init();  //Initialize controller
    ReefAngel.Use2014Screen();  // Let's use 2014 Screen 
    // Ports toggled in Feeding Mode
    ReefAngel.FeedingModePorts = Port5Bit;
    // Ports toggled in Water Change Mode
    ReefAngel.WaterChangePorts = Port3Bit | Port4Bit | Port5Bit;
    // Ports toggled when Lights On / Off menu entry selected
    ReefAngel.LightsOnPorts = Port1Bit | Port2Bit;
    // Ports turned off when Overheat temperature exceeded
    ReefAngel.OverheatShutoffPorts = Port1Bit | Port2Bit | Port3Bit | Port4Bit | Port5Bit | Port7Bit;
    // Use T1 probe as temperature and overheat functions
    ReefAngel.TempProbe = T1_PROBE;
    ReefAngel.OverheatProbe = T1_PROBE;

    // Feeeding and Water Change mode speed
    ReefAngel.DCPump.FeedingSpeed=0;
    ReefAngel.DCPump.WaterChangeSpeed=0;
    
  

    // Ports that are always on
    ReefAngel.Relay.On( Port4 );

    ////// Place additional initialization code below here
    

    ////// Place additional initialization code above here
}

void loop()
{
    ReefAngel.ActinicLights( Port1 );
    ReefAngel.DayLights( Port2 );
    ReefAngel.StandardHeater( Port3 );
    ReefAngel.StandardLights( Port5 );
    ReefAngel.DosingPumpRepeat1( Port6 );
    ReefAngel.DosingPumpRepeat2( Port7 );
    ReefAngel.DosingPumpRepeat3( Port8 );
    ReefAngel.PWM.DaylightPWMParabola();
    ReefAngel.PWM.ActinicPWMParabola();
    ReefAngel.DCPump.LowATOChannel = Sync; // WP40 & SW 8
    ReefAngel.DCPump.HighATOChannel = None; //  
    
    ////// Place your custom code below here
    
    // DC pumps....................................
    static int rmode;
    static boolean changeMode=true;

    // These are the modes we can cycle through. You can add more and even repeat...
    byte modes[] = { ReefCrest, Lagoon, TidalSwell, ShortPulse, Sine, Else, Gyre, NutrientTransport };

    if (now()%1800==0 || changeMode==true)  // Change every 30 mins (1800seconds) or controller reboot
    {
    rmode=random(100)%sizeof(modes); // Change the mode by picking from our array
    changeMode=false;
    }

    // Set timer when in feeding mode
    static unsigned long feeding;
    if (ReefAngel.DisplayedMenu==FEEDING_MODE) feeding=now();
    
    // Continue NutrientTranspot Mode for 30 minutes after feeding
    if (now()-feeding<1800) 
    {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=ReefCrest;
    ReefAngel.DCPump.Speed=80;
    }
    
    // Night/Quiet mode
      else if (hour()>=2 && hour()<8 ) // 2am to 8am
    { 
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.SetMode( Sine,35,10 );
    } 
      else if (hour()>=15 && hour()<19) // 3pm and 7pm
    {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.SetMode( LongPulse,30,1 ); 
    }
    
    //Storm mode
    else if (hour()>=1 && hour()<2) // 1am and 2am
    {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.SetMode( Else,80,15 );  
    }
      else if (hour()>=11 && hour()<12) // 11am and 12pm
    {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.SetMode( LongPulse,95,2 );  
    }
    else if (hour()>=21 && hour()<22) // 9pm and 10pm
    {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.SetMode( ReefCrest,85,15 );  
    }
    
    // Custom Mode and nothing else going on
    else if (InternalMemory.DCPumpMode_read()==11) 
    {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=modes[rmode]; // Put the mode to the random mode :)
    ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Set speed from portal
    } else {
    ReefAngel.DCPump.UseMemory=true; // Will reset all values from memory
    }
    ////// Place your custom code above here

Posted: **Thu Feb 16, 2017 4:16 am**

Code: Select all



////// Place global variable code below here


////// Place global variable code above here


void setup()
{
    // This must be the first line
    InternalMemory.LCDID_write(255); //this line was added when i got a replacement RA+ board
    ReefAngel.Init();  //Initialize controller
    ReefAngel.Use2014Screen();  // Let's use 2014 Screen 
    // Ports toggled in Feeding Mode
    ReefAngel.FeedingModePorts = Port5Bit | Port6Bit;
    // Ports toggled in Water Change Mode
    ReefAngel.WaterChangePorts = Port3Bit | Port4Bit | Port5Bit | Port6Bit;
    // Ports toggled when Lights On / Off menu entry selected
    ReefAngel.LightsOnPorts = Port1Bit | Port2Bit;
    // Ports turned off when Overheat temperature exceeded
    ReefAngel.OverheatShutoffPorts = Port1Bit | Port2Bit | Port3Bit | Port5Bit | Port6Bit;
    // Use T1 probe as temperature and overheat functions
    ReefAngel.TempProbe = T1_PROBE;
    ReefAngel.OverheatProbe = T1_PROBE;

    // Feeeding and Water Change mode speed
    ReefAngel.DCPump.FeedingSpeed=0;
    ReefAngel.DCPump.WaterChangeSpeed=0;
    
  

    // Ports that are always on
    ReefAngel.Relay.On( Port4 );
    

    ////// Place additional initialization code below here
    

    ////// Place additional initialization code above here
}

void loop()
{
    ReefAngel.ActinicLights( Port1 );
    ReefAngel.DayLights( Port2 );
    ReefAngel.StandardHeater( Port3 );
    ReefAngel.Relay.DelayedOn(Port5 );
    ReefAngel.DosingPumpRepeat1( Port7 );
    ReefAngel.DosingPumpRepeat2( Port8 );
    ReefAngel.PWM.DaylightPWMSlope();
    ReefAngel.PWM.ActinicPWMSlope();
    ReefAngel.DCPump.LowATOChannel = Sync; // WP40 
    ReefAngel.DCPump.HighATOChannel = AntiSync; // SW-8
    ReefAngel.DCPump.AntiSyncOffset = 125;
    
    ////// Place your custom code below here
    
    // Wavemaker
    
    if ( ((hour() >= 2) && (hour() < 8)) || ((hour() >= 15) && (hour() < 19)) ) // off from 2am-8am & 3pm-7pm
      {
        ReefAngel.Relay.Off(Port6);
      }
        else
      {
        ReefAngel.WavemakerRandom( Port6, 30, 300 ); // random between 30 and 300 seconds
      }
  
  
    // DC pumps....................................
    static int rmode;
    static boolean changeMode=true;

    // These are the modes we can cycle through. You can add more and even repeat...
    byte modes[] = { ReefCrest, Lagoon, TidalSwell, ShortPulse, Sine, Else, Gyre, NutrientTransport };

    if (now()%1800==0 || changeMode==true)  // Change every 30 mins (1800seconds) or controller reboot
    {
    rmode=random(100)%sizeof(modes); // Change the mode by picking from our array
    changeMode=false;
    }

    // Set timer when in feeding mode
    static unsigned long feeding;
    if (ReefAngel.DisplayedMenu==FEEDING_MODE) feeding=now();
    
    // Continue NutrientTranspot Mode for 30 minutes after feeding
    if (now()-feeding<1800) 
    {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=ReefCrest;
    ReefAngel.DCPump.Speed=75;
    }
    
    // Night/Quiet mode
      else if (hour()>=2 && hour()<8 ) // 2am to 8am
    { 
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.SetMode( Gyre,40,10 );
    } 
      else if (hour()>=15 && hour()<19) // 3pm and 7pm
    {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.SetMode( ShortPulse,40,30 ); 
    }
    
    //Storm mode
    else if (hour()>=1 && hour()<2) // 1am and 2am
    {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.SetMode( Else,70,15 );  
    }
      else if (hour()>=11 && hour()<12) // 11am and 12pm
    {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.SetMode( ReefCrest,80,15 );  
    }
    else if (hour()>=21 && hour()<22) // 9pm and 10pm
    {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.SetMode( ShortPulse,85,30 );  
    }
    
    // Custom Mode and nothing else going on
    else if (InternalMemory.DCPumpMode_read()==11) 
    {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=modes[rmode]; // Put the mode to the random mode :)
    ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Set speed from portal
    } else {
    ReefAngel.DCPump.UseMemory=true; // Will reset all values from memory
    }
    ////// Place your custom code above here

Posted: **Wed Oct 11, 2017 2:36 pm**

Hoping someone can help with this. I'd like to add Seasonal changes to my code but can't get it to compile.

Code: Select all

void SeasonalTemps ()
 {
  static int heatArray[][2] = { {782,786},// default in case of error in month=0 (June)
                    {760,764},//January (winter)
                    {764,768},//February (winter)
                    {765,769},//March (early spring)
                    {769,773},//April (spring)
                    {775,779},//May (spring)
                    {782,786},//June (early summer)
                    {789,793},//July (summer)
                    {796,800},//August (summer)
                    {786,790},//September (early fall)
                    {777,781},//October (fall)
                    {770,774},//November (fall)
                    {765,769} };//December (early winter)
                    
               
  ReefAngel.StandardHeater( Port3,heatArray[month()][0],heatArray[month()][1]);
 }//end seasonalTemps

where exactly do I input this?

Posted: **Thu Oct 12, 2017 7:15 pm**

you have to simply copy the entire function and paste it into your INO file, most likely at the end of it. well after the last curly brace of the loop.

Sent from my XT1585 using Tapatalk

Posted: **Fri Oct 08, 2021 5:15 am**

Code: Select all

#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <DCPump.h>
#include <PAR.h>
#include <ReefAngel.h>

////// Place global variable code below here

void SeasonalTemps ()
 {
  static int heatArray[][2] = { {780,784},// default in case of error in month=0 (May)
                    {764,768},//January (winter)
                    {768,772},//February (winter)
                    {772,776},//March (early spring)
                    {776,780},//April (spring)
                    {780,784},//May (spring)
                    {784,788},//June (early summer)
                    {788,792},//July (summer)
                    {784,788},//August (summer)
                    {780,784},//September (early fall)
                    {776,780},//October (fall)
                    {772,776},//November (fall)
                    {768,772} };//December (early winter)
                   
               
  ReefAngel.StandardHeater( Port1,heatArray[month()][0],heatArray[month()][1]);
 }//end seasonalTemps

////// Place global variable code above here


void setup()
{
    // This must be the first line
    ReefAngel.Init();  //Initialize controller
    ReefAngel.Use2014Screen();  // Let's use 2014 Screen 
    // Ports toggled in Feeding Mode
    ReefAngel.FeedingModePorts = Port5Bit;
    // Ports toggled in Water Change Mode
    ReefAngel.WaterChangePorts = Port1Bit | Port2Bit | Port4Bit;
    // Ports toggled when Lights On / Off menu entry selected
    ReefAngel.LightsOnPorts = Port1Bit | Port2Bit;
    // Ports turned off when Overheat temperature exceeded
    ReefAngel.OverheatShutoffPorts = Port1Bit | Port3Bit | Port4Bit;
    // Use T1 probe as temperature and overheat functions
    ReefAngel.TempProbe = T1_PROBE;
    ReefAngel.OverheatProbe = T1_PROBE;

    // Feeeding and Water Change mode speed
    ReefAngel.DCPump.FeedingSpeed=0;
    ReefAngel.DCPump.WaterChangeSpeed=0;
    
  

    // Ports that are always on
    ReefAngel.Relay.On( Port5 );

    ////// Place additional initialization code below here
    

    ////// Place additional initialization code above here
}

void loop()
{
    SeasonalTemps ();

    ReefAngel.ActinicLights( Port2 ); //ATS pump
    ReefAngel.DayLights( Port3 ); //ATS light
    ReefAngel.StandardLights( Port4, 23,0,7,0); //Skimmer 11pm-7am
    ReefAngel.DosingPumpRepeat1( Port6 );
    ReefAngel.DosingPumpRepeat2( Port7 );
    ReefAngel.DosingPumpRepeat3( Port8 );
    ReefAngel.PWM.DaylightPWMParabola();
    ReefAngel.PWM.ActinicPWMParabola();
    ReefAngel.DCPump.UseMemory = true;
    ReefAngel.DCPump.LowATOChannel = Sync; // SW 8 
    ReefAngel.DCPump.HighATOChannel = AntiSync; // SW 8 
    //ReefAngel.DCPump.AntiSyncOffset = 125; // % (0-255) of main pump (Sync)

    ////// Place your custom code below here
    
    // koralia 1150
    // if (hour()>=23 || hour()<11) ReefAngel.Relay.Off( Port5 );
    // else ReefAngel.WavemakerRandom( Port5, 120, 1800 );
    
    // DC pumps
    // To run this code must choose Custom in portal
    static int rmode;
    static boolean changeMode=true;

    // These are the modes we can cycle through. You can add more and even repeat...
    byte modes[] = { ReefCrest, Lagoon, TidalSwell, ShortPulse, Sine, LongPulse, Else, Gyre, NutrientTransport };

    if (now()%3600==0 || changeMode==true) { // Change every 60 mins (3600seconds) or controller reboot
    rmode=random(100)%sizeof(modes); // Change the mode by picking from our array
    changeMode=false;
    }

    // Set timer when in feeding mode
    static unsigned long feeding;
    if (ReefAngel.DisplayedMenu==FEEDING_MODE) feeding=now();
    // Continue NutrientTranspot Mode for 30 minutes after feeding
    if (now()-feeding<1800) {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=Else;
    ReefAngel.DCPump.Speed=80;
    // Night mode (go to 30%)
    } else if (now()%SECS_PER_DAY<39600 || now()%SECS_PER_DAY>=82800) { // 11pm to 11am
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=Gyre;
    ReefAngel.DCPump.Speed=40;
    } else if (InternalMemory.DCPumpMode_read()==11) {
    // Custom Mode and nothing else going on
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=modes[rmode]; // Put the mode to the random mode :)
    ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Set speed from portal
    } else {
    ReefAngel.DCPump.UseMemory=true; // Will reset all values from memory
    }

    ////// Place your custom code above here

    // This should always be the last line
   
}

Posted: **Mon Jan 31, 2022 8:24 am**

Hoping someone from this great community can help as I'm not sure how to implement this. I'm looking to turn my kalk stirrer (port 7) off between 5pm and 11pm.

if ( hour(now()) >= 17 && hour(now()) <= 23 ) ReefAngel.Relay.Off( Port7 );

if the statement above is correct, where should I input it into my code?

Thanks

Posted: **Mon Jan 31, 2022 11:08 am**

It has to be the line right after the kalkwasser function

Posted: **Mon Jan 31, 2022 1:45 pm**

Hi Roberto,

so like this?

ReefAngel.DosingPumpRepeat1( Port6 );
ReefAngel.DosingPumpRepeat2( Port7 );
if ( hour(now()) >= 17 && hour(now()) <= 23 ) ReefAngel.Relay.Off(Port7 );
ReefAngel.DosingPumpRepeat3( Port8 );

Thanks

Posted: **Mon Jan 31, 2022 1:45 pm**

Yes. Looks good

Posted: **Mon Jan 31, 2022 4:50 pm**

Code: Select all


#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <DCPump.h>
#include <PAR.h>
#include <ReefAngel.h>

////// Place global variable code below here

void SeasonalTemps ()
 {
  static int heatArray[][2] = { {780,784},// default in case of error in month=0 (May)
                    {764,768},//January (winter)
                    {768,772},//February (winter)
                    {772,776},//March (early spring)
                    {776,780},//April (spring)
                    {780,784},//May (spring)
                    {784,788},//June (early summer)
                    {788,792},//July (summer)
                    {784,788},//August (summer)
                    {780,784},//September (early fall)
                    {776,780},//October (fall)
                    {772,776},//November (fall)
                    {768,772} };//December (early winter)
                   
               
  ReefAngel.StandardHeater( Port1,heatArray[month()][0],heatArray[month()][1]);
 }//end seasonalTemps

////// Place global variable code above here


void setup()
{
    // This must be the first line
    ReefAngel.Init();  //Initialize controller
    ReefAngel.Use2014Screen();  // Let's use 2014 Screen 
    // Ports toggled in Feeding Mode
    ReefAngel.FeedingModePorts = Port5Bit;
    // Ports toggled in Water Change Mode
    ReefAngel.WaterChangePorts = Port1Bit | Port3Bit | Port5Bit;
    // Ports toggled when Lights On / Off menu entry selected
    ReefAngel.LightsOnPorts = Port1Bit | Port2Bit;
    // Ports turned off when Overheat temperature exceeded
    ReefAngel.OverheatShutoffPorts = Port1Bit | Port3Bit | Port4Bit;
    // Use T1 probe as temperature and overheat functions
    ReefAngel.TempProbe = T1_PROBE;
    ReefAngel.OverheatProbe = T1_PROBE;

    // Feeeding and Water Change mode speed
    ReefAngel.DCPump.FeedingSpeed=0;
    ReefAngel.DCPump.WaterChangeSpeed=0;
    
  

    // Ports that are always on
    ReefAngel.Relay.On( Port2 );
    ReefAngel.Relay.On( Port5 );

    ////// Place additional initialization code below here
    

    ////// Place additional initialization code above here
}

void loop()
{
    SeasonalTemps();
  
    ReefAngel.ActinicLights( Port3 ); //Skimmer
    ReefAngel.DayLights( Port4 ); //ATS light
    ReefAngel.DosingPumpRepeat1( Port6 );
    ReefAngel.DosingPumpRepeat2( Port7 );
    if ( hour(now()) >= 17 && hour(now()) <= 23 ) ReefAngel.Relay.Off( Port7 ); //kalk dosing off 5pm-11pm
    ReefAngel.DosingPumpRepeat3( Port8 );
    ReefAngel.PWM.DaylightPWMParabola();
    ReefAngel.PWM.ActinicPWMParabola();
    ReefAngel.DCPump.UseMemory = true;
    ReefAngel.DCPump.LowATOChannel = Sync; // SW 8 
    ReefAngel.DCPump.HighATOChannel = AntiSync; // SW 8 
    //ReefAngel.DCPump.AntiSyncOffset = 125; // % (0-255) of main pump (Sync)

    ////// Place your custom code below here
    
    // koralia 1150
    // if (hour()>=23 || hour()<11) ReefAngel.Relay.Off( Port5 );
    // else ReefAngel.WavemakerRandom( Port5, 120, 1800 );
    
    // DC pumps
    // To run this code must choose Custom in portal
    static int rmode;
    static boolean changeMode=true;

    // These are the modes we can cycle through. You can add more and even repeat...
    byte modes[] = { ReefCrest, Lagoon, TidalSwell, ShortPulse, Sine, LongPulse, Else, Gyre, NutrientTransport };

    if (now()%3600==0 || changeMode==true) { // Change every 60 mins (3600seconds) or controller reboot
    rmode=random(100)%sizeof(modes); // Change the mode by picking from our array
    changeMode=false;
    }

    // Set timer when in feeding mode
    static unsigned long feeding;
    if (ReefAngel.DisplayedMenu==FEEDING_MODE) feeding=now();
    // Continue NutrientTranspot Mode for 30 minutes after feeding
    if (now()-feeding<1800) {
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=Else;
    ReefAngel.DCPump.Speed=80;
    // Night mode (go to 30%)
    } else if (now()%SECS_PER_DAY<39600 || now()%SECS_PER_DAY>=82800) { // 11pm to 11am
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=Gyre;
    ReefAngel.DCPump.Speed=40;
    } else if (InternalMemory.DCPumpMode_read()==11) {
    // Custom Mode and nothing else going on
    ReefAngel.DCPump.UseMemory=false;
    ReefAngel.DCPump.Duration=InternalMemory.DCPumpDuration_read();
    ReefAngel.DCPump.Mode=modes[rmode]; // Put the mode to the random mode :)
    ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Set speed from portal
    } else {
    ReefAngel.DCPump.UseMemory=true; // Will reset all values from memory
    }

    ////// Place your custom code above here

Posted: **Mon Jan 31, 2022 9:54 pm**

hey Roberto, didnt work! any other ideas?

Reef Angel Forum

Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code

Re: Reefology's code