RA* shows disconnected
RA* shows disconnected
has ip address but isn't connecting to cloud. is there something in code that I have to enter username and password for it to connect ? uapp is connectiong but not updating. searches isn't turning up anything after a couple hrs
Re: RA* shows disconnected
I see its connecting to the portal
Re: RA* shows disconnected
Yes. When you generate your code using the web wizard, you have to enter the password and it is case sensitive.
Roberto.
Re: RA* shows disconnected
Yeah I did that. I logged in with my old people first. Then realized I needed to change it. I then redid code with new PW add still isn't connecting to cloud. Web based uapp had no problems though
Re: RA* shows disconnected
I'm pretty sure it is the password then.
Did you click encrypt and went all the way to generate and uploaded the code that was generated?
Did you click encrypt and went all the way to generate and uploaded the code that was generated?
Roberto.
Re: RA* shows disconnected
Yes a couple times.. Add changed my PW a couple times also
Re: RA* shows disconnected
Can you post the code you are uploading?
It shows a blank password.
It shows a blank password.
Roberto.
Re: RA* shows disconnected
#include <Salinity.h>
#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_TS.h>
#include <RA_TouchLCD.h>
#include <RA_TFT.h>
#include <RA_TS.h>
#include <Font.h>
#include <RA_Wifi.h>
#include <RA_Wiznet5100.h>
#include <SD.h>
#include <SPI.h>
#include <Ethernet.h>
#include <EthernetDHCP.h>
#include <PubSubClient.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_ATO.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <RA_CustomLabels.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <PAR.h>
#include <DCPump.h>
#include <ReefAngel.h>
#include <SoftwareSerial.h>
////// Place global variable code below here
////// Place global variable code above here
void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
ReefAngel.Star();
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = 0;
ReefAngel.FeedingModePortsE[0] = Port1Bit | Port3Bit;
ReefAngel.FeedingModePortsE[1] = 0;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = 0;
ReefAngel.WaterChangePortsE[0] = Port1Bit | Port3Bit;
ReefAngel.WaterChangePortsE[1] = 0;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = 0;
ReefAngel.OverheatShutoffPortsE[0] = Port2Bit;
ReefAngel.OverheatShutoffPortsE[1] = 0;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = 0;
ReefAngel.LightsOnPortsE[0] = 0;
ReefAngel.LightsOnPortsE[1] = 0;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;
// Set the Overheat temperature setting
InternalMemory.OverheatTemp_write( 805 );
// Ports that are always on
ReefAngel.Relay.On( Box1_Port1 );
ReefAngel.Relay.On( Box1_Port5 );
ReefAngel.Relay.On( Box1_Port6 );
ReefAngel.Relay.On( Box1_Port7 );
ReefAngel.Relay.On( Box1_Port8 );
////// Place additional initialization code below here
////// Place additional initialization code above here
}
void loop()
{
ReefAngel.StandardHeater( T1_PROBE,Box1_Port2,760,770 );
ReefAngel.SingleATO( true,Box1_Port3,180,0 );
ReefAngel.StandardLights( Box1_Port4,10,0,22,0 );
ReefAngel.PWM.SetDaylight( PWMSlope( 9,0,17,0,15,70,60,0 ) );
ReefAngel.PWM.SetActinic( PWMSlope( 9,0,17,0,15,70,60,0 ) );
ReefAngel.PWM.SetDaylight2( PWMSlope( 9,0,17,0,15,70,60,0 ) );
ReefAngel.PWM.SetActinic2( PWMSlope( 9,0,17,0,15,70,60,0 ) );
boolean buzzer=false;
if ( buzzer ) ReefAngel.BuzzerOn(2); else ReefAngel.BuzzerOff();
////// Place your custom code below here
////// Place your custom code above here
ReefAngel.Network.Cloud();
// This should always be the last line
ReefAngel.ShowTouchInterface();
}
// RA_STRING1=U2FsdGVkX19l4rVch5Wsz3j92ZZ1yaCjltVKjB3fddY=
// RA_STRING2=null
// RA_STRING3=null
// RA_LABEL LABEL_PORT11=Return
// RA_LABEL LABEL_PORT12=Heater
// RA_LABEL LABEL_PORT13=ATO
// RA_LABEL LABEL_PORT14=ReefBrite
// RA_LABEL LABEL_PORT15=Skimmer
#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_TS.h>
#include <RA_TouchLCD.h>
#include <RA_TFT.h>
#include <RA_TS.h>
#include <Font.h>
#include <RA_Wifi.h>
#include <RA_Wiznet5100.h>
#include <SD.h>
#include <SPI.h>
#include <Ethernet.h>
#include <EthernetDHCP.h>
#include <PubSubClient.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_ATO.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <RA_CustomLabels.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <PAR.h>
#include <DCPump.h>
#include <ReefAngel.h>
#include <SoftwareSerial.h>
////// Place global variable code below here
////// Place global variable code above here
void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
ReefAngel.Star();
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = 0;
ReefAngel.FeedingModePortsE[0] = Port1Bit | Port3Bit;
ReefAngel.FeedingModePortsE[1] = 0;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = 0;
ReefAngel.WaterChangePortsE[0] = Port1Bit | Port3Bit;
ReefAngel.WaterChangePortsE[1] = 0;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = 0;
ReefAngel.OverheatShutoffPortsE[0] = Port2Bit;
ReefAngel.OverheatShutoffPortsE[1] = 0;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = 0;
ReefAngel.LightsOnPortsE[0] = 0;
ReefAngel.LightsOnPortsE[1] = 0;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;
// Set the Overheat temperature setting
InternalMemory.OverheatTemp_write( 805 );
// Ports that are always on
ReefAngel.Relay.On( Box1_Port1 );
ReefAngel.Relay.On( Box1_Port5 );
ReefAngel.Relay.On( Box1_Port6 );
ReefAngel.Relay.On( Box1_Port7 );
ReefAngel.Relay.On( Box1_Port8 );
////// Place additional initialization code below here
////// Place additional initialization code above here
}
void loop()
{
ReefAngel.StandardHeater( T1_PROBE,Box1_Port2,760,770 );
ReefAngel.SingleATO( true,Box1_Port3,180,0 );
ReefAngel.StandardLights( Box1_Port4,10,0,22,0 );
ReefAngel.PWM.SetDaylight( PWMSlope( 9,0,17,0,15,70,60,0 ) );
ReefAngel.PWM.SetActinic( PWMSlope( 9,0,17,0,15,70,60,0 ) );
ReefAngel.PWM.SetDaylight2( PWMSlope( 9,0,17,0,15,70,60,0 ) );
ReefAngel.PWM.SetActinic2( PWMSlope( 9,0,17,0,15,70,60,0 ) );
boolean buzzer=false;
if ( buzzer ) ReefAngel.BuzzerOn(2); else ReefAngel.BuzzerOff();
////// Place your custom code below here
////// Place your custom code above here
ReefAngel.Network.Cloud();
// This should always be the last line
ReefAngel.ShowTouchInterface();
}
// RA_STRING1=U2FsdGVkX19l4rVch5Wsz3j92ZZ1yaCjltVKjB3fddY=
// RA_STRING2=null
// RA_STRING3=null
// RA_LABEL LABEL_PORT11=Return
// RA_LABEL LABEL_PORT12=Heater
// RA_LABEL LABEL_PORT13=ATO
// RA_LABEL LABEL_PORT14=ReefBrite
// RA_LABEL LABEL_PORT15=Skimmer
Re: RA* shows disconnected
That yields a blank password.
Make sure you type the password and hit encrypt and go all the way to the end of the wizard and click generate.
Make sure you type the password and hit encrypt and go all the way to the end of the wizard and click generate.
Roberto.
Re: RA* shows disconnected
That's what I thought when I looked at it. That's why I asked about the code. So even though I don't have any attachments or expansions I can't click over them on the left? I have been clicking encrypt after every pw
Re: RA* shows disconnected
I just went through it clicking next everytime and I'm still not seeing a pw
#include <Salinity.h>
#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_TS.h>
#include <RA_TouchLCD.h>
#include <RA_TFT.h>
#include <RA_TS.h>
#include <Font.h>
#include <RA_Wifi.h>
#include <RA_Wiznet5100.h>
#include <SD.h>
#include <SPI.h>
#include <Ethernet.h>
#include <EthernetDHCP.h>
#include <PubSubClient.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_ATO.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <RA_CustomLabels.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <PAR.h>
#include <DCPump.h>
#include <ReefAngel.h>
#include <SoftwareSerial.h>
////// Place global variable code below here
////// Place global variable code above here
void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
ReefAngel.Star();
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = 0;
ReefAngel.FeedingModePortsE[0] = Port1Bit | Port3Bit;
ReefAngel.FeedingModePortsE[1] = 0;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = 0;
ReefAngel.WaterChangePortsE[0] = Port1Bit | Port3Bit;
ReefAngel.WaterChangePortsE[1] = 0;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = 0;
ReefAngel.OverheatShutoffPortsE[0] = Port2Bit;
ReefAngel.OverheatShutoffPortsE[1] = 0;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = 0;
ReefAngel.LightsOnPortsE[0] = 0;
ReefAngel.LightsOnPortsE[1] = 0;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;
// Set the Overheat temperature setting
InternalMemory.OverheatTemp_write( 805 );
// Ports that are always on
ReefAngel.Relay.On( Box1_Port1 );
ReefAngel.Relay.On( Box1_Port5 );
ReefAngel.Relay.On( Box1_Port6 );
ReefAngel.Relay.On( Box1_Port7 );
ReefAngel.Relay.On( Box1_Port8 );
////// Place additional initialization code below here
////// Place additional initialization code above here
}
void loop()
{
ReefAngel.StandardHeater( T1_PROBE,Box1_Port2,760,770 );
ReefAngel.SingleATO( true,Box1_Port3,180,0 );
ReefAngel.StandardLights( Box1_Port4,10,0,22,0 );
ReefAngel.PWM.SetDaylight( PWMSlope( 9,0,17,0,15,70,60,0 ) );
ReefAngel.PWM.SetActinic( PWMSlope( 9,0,17,0,15,70,60,0 ) );
ReefAngel.PWM.SetDaylight2( PWMSlope( 9,0,17,0,15,70,60,0 ) );
ReefAngel.PWM.SetActinic2( PWMSlope( 9,0,17,0,15,70,60,0 ) );
boolean buzzer=false;
if ( buzzer ) ReefAngel.BuzzerOn(2); else ReefAngel.BuzzerOff();
////// Place your custom code below here
////// Place your custom code above here
ReefAngel.Network.Cloud();
// This should always be the last line
ReefAngel.ShowTouchInterface();
}
// RA_STRING1=U2FsdGVkX19l4rVch5Wsz3j92ZZ1yaCjltVKjB3fddY=
// RA_STRING2=null
// RA_STRING3=null
// RA_LABEL LABEL_PORT11=Return
// RA_LABEL LABEL_PORT12=Heater
// RA_LABEL LABEL_PORT13=ATO
// RA_LABEL LABEL_PORT14=ReefBrite
// RA_LABEL LABEL_PORT15=Skimmer
#include <Salinity.h>
#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_TS.h>
#include <RA_TouchLCD.h>
#include <RA_TFT.h>
#include <RA_TS.h>
#include <Font.h>
#include <RA_Wifi.h>
#include <RA_Wiznet5100.h>
#include <SD.h>
#include <SPI.h>
#include <Ethernet.h>
#include <EthernetDHCP.h>
#include <PubSubClient.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_ATO.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <RA_CustomLabels.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <PAR.h>
#include <DCPump.h>
#include <ReefAngel.h>
#include <SoftwareSerial.h>
////// Place global variable code below here
////// Place global variable code above here
void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
ReefAngel.Star();
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = 0;
ReefAngel.FeedingModePortsE[0] = Port1Bit | Port3Bit;
ReefAngel.FeedingModePortsE[1] = 0;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = 0;
ReefAngel.WaterChangePortsE[0] = Port1Bit | Port3Bit;
ReefAngel.WaterChangePortsE[1] = 0;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = 0;
ReefAngel.OverheatShutoffPortsE[0] = Port2Bit;
ReefAngel.OverheatShutoffPortsE[1] = 0;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = 0;
ReefAngel.LightsOnPortsE[0] = 0;
ReefAngel.LightsOnPortsE[1] = 0;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;
// Set the Overheat temperature setting
InternalMemory.OverheatTemp_write( 805 );
// Ports that are always on
ReefAngel.Relay.On( Box1_Port1 );
ReefAngel.Relay.On( Box1_Port5 );
ReefAngel.Relay.On( Box1_Port6 );
ReefAngel.Relay.On( Box1_Port7 );
ReefAngel.Relay.On( Box1_Port8 );
////// Place additional initialization code below here
////// Place additional initialization code above here
}
void loop()
{
ReefAngel.StandardHeater( T1_PROBE,Box1_Port2,760,770 );
ReefAngel.SingleATO( true,Box1_Port3,180,0 );
ReefAngel.StandardLights( Box1_Port4,10,0,22,0 );
ReefAngel.PWM.SetDaylight( PWMSlope( 9,0,17,0,15,70,60,0 ) );
ReefAngel.PWM.SetActinic( PWMSlope( 9,0,17,0,15,70,60,0 ) );
ReefAngel.PWM.SetDaylight2( PWMSlope( 9,0,17,0,15,70,60,0 ) );
ReefAngel.PWM.SetActinic2( PWMSlope( 9,0,17,0,15,70,60,0 ) );
boolean buzzer=false;
if ( buzzer ) ReefAngel.BuzzerOn(2); else ReefAngel.BuzzerOff();
////// Place your custom code below here
////// Place your custom code above here
ReefAngel.Network.Cloud();
// This should always be the last line
ReefAngel.ShowTouchInterface();
}
// RA_STRING1=U2FsdGVkX19l4rVch5Wsz3j92ZZ1yaCjltVKjB3fddY=
// RA_STRING2=null
// RA_STRING3=null
// RA_LABEL LABEL_PORT11=Return
// RA_LABEL LABEL_PORT12=Heater
// RA_LABEL LABEL_PORT13=ATO
// RA_LABEL LABEL_PORT14=ReefBrite
// RA_LABEL LABEL_PORT15=Skimmer
Re: RA* shows disconnected
Doesn't make sense.
// RA_STRING1=U2FsdGVkX19l4rVch5Wsz3j92ZZ1yaCjltVKjB3fddY=
This is still a blank password.
Can you click encrypt after you type the password and send what it shows on the screen as encrypted password?
Then go to the end and generate. See if it matches.
If it does, I would try a different browser.
// RA_STRING1=U2FsdGVkX19l4rVch5Wsz3j92ZZ1yaCjltVKjB3fddY=
This is still a blank password.
Can you click encrypt after you type the password and send what it shows on the screen as encrypted password?
Then go to the end and generate. See if it matches.
If it does, I would try a different browser.
Roberto.
Re: RA* shows disconnected
I just put PW in and got encrypt.... That string is what does in the box for forum password
Edit: string is different but starts out like it
Edit: string is different but starts out like it
Re: RA* shows disconnected
Changed to come from IE .. Finally got connected.. Not sure why IE was having problems
Thanks Roberto
Thanks Roberto