Wifi Error

[rimai]

Can you paste the log of the factory reset?

[deputy1234]

Can you paste the log of the factory reset?

Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
< CMD
> set u b 57600
< set u b 57600
< AOK
< <4.41>
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 86328 3 wifly-GSX-400
< 4 74920 3 web_app-GSX-106
< 7 46632 3 wps_app-GSX-131
< 9 66240 3 eap_app-GSX-101
< 11 37282 0 web_config.html
< 21 512 0 link.html
< 22 7268 0 logo.png
< 24 1052 10 config
< 25 944 10 user
< 26 88548 3 wifly-GSX-441-r1057
<
< 145 Free, Boot=26, Backup=2
< <4.41>
> load user
< load user
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.41>
> set w l 5
< set w l 5
< AOK
< <4.41>
> set w s Dhouse
< set w s Dhouse
< AOK
< <4.41>
> set w p 5198545981
< set w p 5198545981
< AOK
< <4.41>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.41>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> reboot
< reboot
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.

Removing connection to COM4
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
< CMD
> set u b 57600
< set u b 57600
< AOK
< <4.41>
> set s p 0
> save
< <4.41>
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 86328 3 wifly-GSX-400
< 4 74920 3 web_app-GSX-106
< 7 46632 3 wps_app-GSX-131
< 9 66240 3 eap_app-GSX-101
< 11 37282 0 web_config.html
< 21 512 0 link.html
< 22 7268 0 logo.png
< 24 1052 10 config
< 25 944 10 user
< 26 88548 3 wifly-GSX-441-r1057
<
< 145 Free, Boot=26, Backup=2
< <4.41>
> load user
< load user
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.41>
> set w l 5
< set w l 5
< AOK
< <4.41>
> set w s Dhouse
< set w s Dhouse
< AOK
< <4.41>
> set w p 5198545981
< set w p 5198545981
< AOK
< <4.41>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.41>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> reboot
< reboot
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.

Removing connection to COM4
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
< CMD
> factory RESET
< factory RESET
< Set Factory Defaults
> reboot
< <4.41>
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Factory Settings Restored
---------------------------------------------------------------------

Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 86328 3 wifly-GSX-400
< 4 74920 3 web_app-GSX-106
< 7 46632 3 wps_app-GSX-131
< 9 66240 3 eap_app-GSX-101
< 11 37282 0 web_config.html
< 21 512 0 link.html
< 22 7268 0 logo.png
< 24 1052 10 config
< 25 944 10 user
< 26 88548 3 wifly-GSX-441-r1057
<
< 145 Free, Boot=26, Backup=2
< <4.41>
> load user
< load user
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.41>
> set w l 5
< set w l 5
< AOK
< <4.41>
> set w s Dhouse
< set w s Dhouse
< AOK
< <4.41>
> set w p 5198545981
< set w p 5198545981
< AOK
< <4.41>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.41>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> reboot
< reboot
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.

Removing connection to COM4
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
< CMD
> set u b 57600
< set u b 57600
< AOK
< <4.41>
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
< CMD
> factory RESET
< factory RESET
< Set Factory Defaults
> reboot
< <4.41>
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Factory Settings Restored
---------------------------------------------------------------------

Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 86328 3 wifly-GSX-400
< 4 74920 3 web_app-GSX-106
< 7 46632 3 wps_app-GSX-131
< 9 66240 3 eap_app-GSX-101
< 11 37282 0 web_config.html
< 21 512 0 link.html
< 22 7268 0 logo.png
< 24 1052 10 config
< 25 944 10 user
< 26 88548 3 wifly-GSX-441-r1057
<
< 145 Free, Boot=26, Backup=2
< <4.41>
> load user
< load user
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.41>
> set w l 5
< set w l 5
< AOK
< <4.41>
> set w s Dhouse
< set w s Dhouse
< AOK
< <4.41>
> set w p 5198545981
< set w p 5198545981
< AOK
< <4.41>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.41>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> reboot
< reboot
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.

Removing connection to COM4
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
< CMD
> set u b 57600
< set u b 57600
< AOK
< <4.41>
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 86328 3 wifly-GSX-400
< 4 74920 3 web_app-GSX-106
< 7 46632 3 wps_app-GSX-131
< 9 66240 3 eap_app-GSX-101
< 11 37282 0 web_config.html
< 21 512 0 link.html
< 22 7268 0 logo.png
< 24 1052 10 config
< 25 944 10 user
< 26 88548 3 wifly-GSX-441-r1057
<
< 145 Free, Boot=26, Backup=2
< <4.41>
> load user
< load user
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.41>
> set w l 5
< set w l 5
< AOK
< <4.41>
> set w s Dhouse
< set w s Dhouse
< AOK
< <4.41>
> set w p 5198545981
< set w p 5198545981
< AOK
< <4.41>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.41>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> reboot
< reboot
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.

Removing connection to COM4
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
< CMD
> set u b 57600
< set u b 57600
< AOK
< <4.41>
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 86328 3 wifly-GSX-400
< 4 74920 3 web_app-GSX-106
< 7 46632 3 wps_app-GSX-131
< 9 66240 3 eap_app-GSX-101
< 11 37282 0 web_config.html
< 21 512 0 link.html
< 22 7268 0 logo.png
< 24 1052 10 config
< 25 944 10 user
< 26 88548 3 wifly-GSX-441-r1057
<
< 145 Free, Boot=26, Backup=2
< <4.41>
> load user
< load user
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.41>
> set w l 5
< set w l 5
< AOK
< <4.41>
> set w s Dhouse
< set w s Dhouse
< AOK
< <4.41>
> set w p 5198545981
< set w p 5198545981
< AOK
< <4.41>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.41>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> reboot
< reboot
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.

Removing connection to COM4
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
< CMD
> set u b 57600
< set u b 57600
< AOK
< <4.41>
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
< CMD
> factory RESET
< factory RESET
< Set Factory Defaults
> reboot
< <4.41>
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Factory Settings Restored
---------------------------------------------------------------------

Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 86328 3 wifly-GSX-400
< 4 74920 3 web_app-GSX-106
< 7 46632 3 wps_app-GSX-131
< 9 66240 3 eap_app-GSX-101
< 11 37282 0 web_config.html
< 21 512 0 link.html
< 22 7268 0 logo.png
< 24 1052 10 config
< 25 944 10 user
< 26 88548 3 wifly-GSX-441-r1057
<
< 145 Free, Boot=26, Backup=2
< <4.41>
> load user
< load user
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.41>
> set w l 5
< set w l 5
< AOK
< <4.41>
> set w s Dhouse
< set w s Dhouse
< AOK
< <4.41>
> set w p 5198545981
< set w p 5198545981
< AOK
< <4.41>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.41>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> reboot
< reboot
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.

Removing connection to COM4
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
< CMD
> set u b 57600
< set u b 57600
< AOK
< <4.41>
> set s p 0
> save
< <4.41>
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
< CMD
> factory RESET
< factory RESET
< Set Factory Defaults
> reboot
< <4.41>
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Factory Settings Restored
---------------------------------------------------------------------

Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.

Removing connection to COM4
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
< CMD
> set u b 57600
< set u b 57600
< AOK
< <4.41>
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 86328 3 wifly-GSX-400
< 4 74920 3 web_app-GSX-106
< 7 46632 3 wps_app-GSX-131
< 9 66240 3 eap_app-GSX-101
< 11 37282 0 web_config.html
< 21 512 0 link.html
< 22 7268 0 logo.png
< 24 1052 10 config
< 25 944 10 user
< 26 88548 3 wifly-GSX-441-r1057
<
< 145 Free, Boot=26, Backup=2
< <4.41>
> load user
< load user
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.41>
> set w l 5
< set w l 5
< AOK
< <4.41>
> set w s Dhouse
< set w s Dhouse
< AOK
< <4.41>
> set w p 5198545981
< set w p 5198545981
< AOK
< <4.41>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.41>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.41>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.41>
> reboot
< reboot
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.

Removing connection to COM4
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
< CMD
> set u b 57600
< set u b 57600
< AOK
< <4.41>
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
< CMD
> factory RESET
< factory RESET
< Set Factory Defaults
> reboot
< <4.41>
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Factory Settings Restored
---------------------------------------------------------------------

Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM4
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM4
Connected to serial port COM4
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Wifi Attachment Connected to COM4
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM4
> $$$
< CMD
> factory RESET
< factory RESET
< Set Factory Defaults
> reboot
< <4.41>
< reboot
Removing connection to COM4
---------------------------------------------------------------------
Factory Settings Restored
---------------------------------------------------------------------

[rimai]

How did you update the firmware?

[deputy1234]

How did you update the firmware?

I updated the firmware through wifi Utility but received the error message ** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.

[rimai]

Are you sure that you are using the correct SSID and passphrase? They are case sensitive, so uppercase and lowercase matters.
The update firmware button is not working.
What's making me confused is the fact that in order to update firmware, you must be connected to wifi in the first place. So, even if the button was working, there would be no way to download new firmware.
Unless you had it connected. Was the unit ever connected to the internet before?
Did you ever connect to the module using teraterm or putty?
I think we need to wipe out the config file and start from scratch.
I need to update one of my units to see how to do that.

[deputy1234]

Are you sure that you are using the correct SSID and passphrase? They are case sensitive, so uppercase and lowercase matters.
The update firmware button is not working.
What's making me confused is the fact that in order to update firmware, you must be connected to wifi in the first place. So, even if the button was working, there would be no way to download new firmware.
Unless you had it connected. Was the unit ever connected to the internet before?
Did you ever connect to the module using teraterm or putty?
I think we need to wipe out the config file and start from scratch.
I need to update one of my units to see how to do that.

Yes the SSID and passphrase are correct.
I did have the wifi connected and then tried to update but received the error message.
I was able connect to teraterm. I tried it last nigh to factory reset but I was not sure how to.

[rimai]

Ok, I was able to replicate the issue and it was definitely due to the firmware upgrade.
Let's try this:
You need to decompress the zip file.
Open the .ttl file in notepad or any other text editor.
Change the SSID and passphrase.
Save the file.
Use Tera Term and go to menu Control->Macro
Browse to the .ttl file you just edited.
It should configure the module at the end of the process.
If you don't get anything in the screen, you will need to change the baud rate before you open the .ttl file.
Go to menu Setup->Serial port and choose 57600 baud and then go to menu Control->Macro to open the .ttl file.
If that does not work for some reason, copy and paste what you get on the screen.

[deputy1234]

Ok, I was able to replicate the issue and it was definitely due to the firmware upgrade.
Let's try this:
You need to decompress the zip file.
Open the .ttl file in notepad or any other text editor.
Change the SSID and passphrase.
Save the file.
Use Tera Term and go to menu Control->Macro
Browse to the .ttl file you just edited.
It should configure the module at the end of the process.
If you don't get anything in the screen, you will need to change the baud rate before you open the .ttl file.
Go to menu Setup->Serial port and choose 57600 baud and then go to menu Control->Macro to open the .ttl file.
If that does not work for some reason, copy and paste what you get on the screen.

Thank you for all your help Roberto!!! it's working!

[Drew471]

Ok I am going to play the noob here. Do you need to setup using the wifi utility first or will this due the setup as well (so I should do the factory reset) . I follow the directions and I get a green blinking light meaning ip a dress ok.... What does that mean?

Sent from my SPH-L720 using Tapatalk

[rimai]

It means you are good to go.
Don't update the firmware as it will cause you to have problems mentioned in this thread.

[AquaO]

I have the same issue...
I tried to update firmware today and have exactly the same problem. My wifi works well for a year. I thought to do well when I make this "update"

I will tried that is mentioned in this post...

Thank

[AquaO]

It's back to work

Thank for this thread!!

[JDP1130]

looks like i have same issue and i am unable to use this wor work correctly. seems as though i cannot get code to push to wifi attachment.

[rimai]

Did you update the firmware?
Is the module blinking blue and green?
Can you paste the log from the wifi utility?

[ahmed]

i have same issue any idea?

[Ferdi]

Hi all, hope everyone is doing well. Im experiencing the same thing as everyone experienced back in 2012.

I followed all the steps in the thread with the file attached and it still doesn’t want to work.

I did change it ip,ssid and password to mine but still no luck.

Maybe there is a small simple thing im doing wrong that I can’t pick up.

Can i perhaps paste the code here and maybe someone might pick up what im totally missing?

[rimai]

Can you post the log of what you get on tera term?

[Ferdi]

There is no log.

A small window pops up for confirmation and shows that its running but after a while it asks again to configure and so it goes on the whole time

[rimai]

Your cable may be bad then