Wifi will not connect after firmware update

Expansion modules and attachments
MortenB
Posts: 6
Joined: Tue Jun 19, 2012 3:14 pm

Re: Wifi will not connect after firmware update

Post by MortenB »

Is this supposed to be a one-time fix? I've done this several times now and each time, the WiFi works for a few weeks and then stop working until I run the macro again, rinse & repeat. Thanks, MB
psirex
Posts: 16
Joined: Tue Jun 11, 2013 8:44 am

Re: Wifi will not connect after firmware update

Post by psirex »

Getting only flashing Green > Blue > Green > Blue > Blue > Green.... Is there a limitation on what the password can contain?
rimai
Posts: 12881
Joined: Fri Mar 18, 2011 6:47 pm

Re: Wifi will not connect after firmware update

Post by rimai »

blue means it is not connected to your wifi network.
Did you try moving closer?
Was there any change in the router?
What security do you have in your router? Try WPA2-PSK.
Roberto.
anderzon_
Posts: 69
Joined: Sun Oct 27, 2013 11:35 am

Re: Wifi will not connect after firmware update

Post by anderzon_ »

Having problem with this. Cant get the wifi to work. This is my file i have used in teraterm:

x=0
while x<>121

messagebox 'Start WiFly module configuration' 'Webscan Config Program'

;this macro all sent with 5 msec character delay
timeout=10
send '$$$'
wait 'CMD'
sendln 'factory RESET'
wait 'Set Factory Defaults'

sendln 'reboot'
wait '*READY*'

;----------------------------------------
; Begin user settings


send '$$$'
wait 'CMD'
sendln 'set ftp address 198.175.253.161'
wait'AOK'
sendln 'save'
wait 'config'
sendln 'set wlan ssid Asus'
wait 'AOK'
sendln 'set wlan pass "my router pass"'
wait 'AOK'
sendln 'set option deviceid ReefAngelWifi'
wait 'AOK'
sendln 'set w j 1'
wait 'AOK'
sendln 'set c c 0'
wait 'AOK'
sendln 'set c r 0'
wait 'AOK'
sendln 'set c o 0'
wait 'AOK'
sendln 'set i d 1'
wait 'AOK'
sendln 'set c i 3'
wait 'AOK'
sendln 'set dns name www.reefangel.com'
wait 'AOK'
sendln 'set i h 104.36.18.155'
wait 'AOK'
sendln 'set i r 80'
wait 'AOK'
sendln 'set i f 0x06'
wait 'AOK'
sendln 'set s t 0x10'
wait 'AOK'
sendln 'set u m 2'
wait 'AOK'
sendln 'set i p 2'
wait 'AOK'
sendln 'set u b 57600'
wait 'AOK'
sendln 'set s p 0'
wait 'AOK'
sendln 'set c s 1420'
wait 'AOK'

sendln 'save'
wait 'config'

sendln 'save user'
wait 'user'

sendln'reboot'


;inputbox 'Configure another module (y/n)' 'WiFly Config Program'

; convert inputstr to ASCII int value
; str2code x inputstr

endwhile



When i load the macro it say Webscan Config Program, and then its couting up to 65 or something, then the same Webscan Config Program comes again and again. Never a message thats its done and ok. Whats should i do to fix it?
Post Reply