wifi and setup issues
wifi and setup issues
Hey im sure I could look on the forums for hours and figure this out but im hoping someone can lead me in the right direction first. I connect the wifi attachment to the cables and run the program but its not letting me select the serial port. I purchased this RA unit from a friend it has way old software and stuff on it already I need to clean it all up and reinstall. having all sorts of problems connecting to it idk.
Re: wifi and setup issues
When I plug the wifi controller in the green and blue lights flash so its hooked up to atleast have power should be doing something
Re: wifi and setup issues
If it is not showing up serial ports, you may not have the usb cable installed correctly.
If you go to device manager on your computer, do you see anything missing drivers?
If you go to device manager on your computer, do you see anything missing drivers?
Roberto.
Re: wifi and setup issues
yah I installed a driver got it to do setup and setup the wifi attachment but its giving me this...
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ftp u
< ftp u
< <4.00>
< FTP connecting to 198.175.253.161
< FTP timeout=2
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> factory RESET
< factory RESET
< Set Factory Defaults
> reboot
< <4.00>
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Factory Settings Restored
---------------------------------------------------------------------
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ftp u
< ftp u
< <4.00>
< FTP connecting to 198.175.253.161
< FTP timeout=2
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 78524 3 WiFly_GSX-2.32
< 22 44704 3 wps_app
< 33 -1 10 config
< 34 78524 3 WiFly_GSX-2.32
< 54 49072 3 wps_app
< 67 -1 10 user
< 68 86328 3 wifly-GSX-400
<
< 166 Free, Boot=68, Backup=34
< <4.00>
> load user
< load user
< AOK
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.00>
> set w l 5
< set w l 5
< AOK
< <4.00>
> set w s �MOTOROLA-C7B82
< set w s ?MOTOROLA-C7B82
< AOK
< <4.00>
> set w p a4a2d35a44912fefbeef
< set w p a4a2d35a44912fefbeef
< AOK
< <4.00>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.00>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> reboot
< reboot
> $$$
< CMD
> show n
< show n
< SSid=?MOTOROLA-C7B82
< Chan=6
< Assoc=FAIL
< Rate=12, 24Mb
< Auth=FAIL
< Mode=NONE
< DHCP=FAIL
< Boot=0
< Time=OK
< Links=0
< <4.00>
> get i
< get i
< IF=DOWN
< DHCP=ON
< IP=10.1.10.20:2000
< NM=255.255.255.0
< GW=10.1.10.1
< HOST=198.171.134.6:80
< PROTO=TCP,
< MTU=1524
< FLAGS=0x6
< TCPMODE=0x0
< BACKUP=0.0.0.0
< <4.00>
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Your Reef Angel Wifi Attachment is now configured with the settings provided.
---------------------------------------------------------------------
If the blue LED is still blinking, it means that the Reef Angel Wifi Attachment could not connect to your wifi network.
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ftp u
< ftp u
< <4.00>
< FTP connecting to 198.175.253.161
< FTP timeout=2
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 78524 3 WiFly_GSX-2.32
< 22 44704 3 wps_app
< 33 -1 10 config
< 34 78524 3 WiFly_GSX-2.32
< 54 49072 3 wps_app
< 67 -1 10 user
< 68 86328 3 wifly-GSX-400
<
< 166 Free, Boot=68, Backup=34
< <4.00>
> load user
< load user
< AOK
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.00>
> set w l 5
< set w l 5
< AOK
< <4.00>
> set w s �MOTOROLA-C7B82
< set w s ?MOTOROLA-C7B82
< AOK
< <4.00>
> set w p a4a2d35a44912fefbeef
< set w p a4a2d35a44912fefbeef
< AOK
< <4.00>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.00>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> reboot
< reboot
> $$$
< CMD
> show n
< show n
< SSid=?MOTOROLA-C7B82
< Chan=6
< Assoc=FAIL
< Rate=12, 24Mb
< Auth=FAIL
< Mode=NONE
< DHCP=FAIL
< Boot=0
< Time=OK
< Links=0
< <4.00>
> get i
< get i
< IF=DOWN
< DHCP=ON
< IP=10.1.10.20:2000
< NM=255.255.255.0
< GW=10.1.10.1
< HOST=198.171.134.6:80
< PROTO=TCP,
< MTU=1524
< FLAGS=0x6
< TCPMODE=0x0
< BACKUP=0.0.0.0
< <4.00>
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Your Reef Angel Wifi Attachment is now configured with the settings provided.
---------------------------------------------------------------------
If the blue LED is still blinking, it means that the Reef Angel Wifi Attachment could not connect to your wifi network.
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ftp u
< ftp u
< <4.00>
< FTP connecting to 198.175.253.161
< FTP timeout=2
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> factory RESET
< factory RESET
< Set Factory Defaults
> reboot
< <4.00>
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Factory Settings Restored
---------------------------------------------------------------------
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ftp u
< ftp u
< <4.00>
< FTP connecting to 198.175.253.161
< FTP timeout=2
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 78524 3 WiFly_GSX-2.32
< 22 44704 3 wps_app
< 33 -1 10 config
< 34 78524 3 WiFly_GSX-2.32
< 54 49072 3 wps_app
< 67 -1 10 user
< 68 86328 3 wifly-GSX-400
<
< 166 Free, Boot=68, Backup=34
< <4.00>
> load user
< load user
< AOK
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.00>
> set w l 5
< set w l 5
< AOK
< <4.00>
> set w s �MOTOROLA-C7B82
< set w s ?MOTOROLA-C7B82
< AOK
< <4.00>
> set w p a4a2d35a44912fefbeef
< set w p a4a2d35a44912fefbeef
< AOK
< <4.00>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.00>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> reboot
< reboot
> $$$
< CMD
> show n
< show n
< SSid=?MOTOROLA-C7B82
< Chan=6
< Assoc=FAIL
< Rate=12, 24Mb
< Auth=FAIL
< Mode=NONE
< DHCP=FAIL
< Boot=0
< Time=OK
< Links=0
< <4.00>
> get i
< get i
< IF=DOWN
< DHCP=ON
< IP=10.1.10.20:2000
< NM=255.255.255.0
< GW=10.1.10.1
< HOST=198.171.134.6:80
< PROTO=TCP,
< MTU=1524
< FLAGS=0x6
< TCPMODE=0x0
< BACKUP=0.0.0.0
< <4.00>
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Your Reef Angel Wifi Attachment is now configured with the settings provided.
---------------------------------------------------------------------
If the blue LED is still blinking, it means that the Reef Angel Wifi Attachment could not connect to your wifi network.
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ftp u
< ftp u
< <4.00>
< FTP connecting to 198.175.253.161
< FTP timeout=2
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> factory RESET
< factory RESET
< Set Factory Defaults
> reboot
< <4.00>
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Factory Settings Restored
---------------------------------------------------------------------
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ftp u
< ftp u
< <4.00>
< FTP connecting to 198.175.253.161
< FTP timeout=2
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 78524 3 WiFly_GSX-2.32
< 22 44704 3 wps_app
< 33 -1 10 config
< 34 78524 3 WiFly_GSX-2.32
< 54 49072 3 wps_app
< 67 -1 10 user
< 68 86328 3 wifly-GSX-400
<
< 166 Free, Boot=68, Backup=34
< <4.00>
> load user
< load user
< AOK
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.00>
> set w l 5
< set w l 5
< AOK
< <4.00>
> set w s �MOTOROLA-C7B82
< set w s ?MOTOROLA-C7B82
< AOK
< <4.00>
> set w p a4a2d35a44912fefbeef
< set w p a4a2d35a44912fefbeef
< AOK
< <4.00>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.00>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> reboot
< reboot
> $$$
< CMD
> show n
< show n
< SSid=?MOTOROLA-C7B82
< Chan=6
< Assoc=FAIL
< Rate=12, 24Mb
< Auth=FAIL
< Mode=NONE
< DHCP=FAIL
< Boot=0
< Time=OK
< Links=0
< <4.00>
> get i
< get i
< IF=DOWN
< DHCP=ON
< IP=10.1.10.20:2000
< NM=255.255.255.0
< GW=10.1.10.1
< HOST=198.171.134.6:80
< PROTO=TCP,
< MTU=1524
< FLAGS=0x6
< TCPMODE=0x0
< BACKUP=0.0.0.0
< <4.00>
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Your Reef Angel Wifi Attachment is now configured with the settings provided.
---------------------------------------------------------------------
If the blue LED is still blinking, it means that the Reef Angel Wifi Attachment could not connect to your wifi network.
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ftp u
< ftp u
< <4.00>
< FTP connecting to 198.175.253.161
< FTP timeout=2
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 78524 3 WiFly_GSX-2.32
< 22 44704 3 wps_app
< 33 -1 10 config
< 34 78524 3 WiFly_GSX-2.32
< 54 49072 3 wps_app
< 67 -1 10 user
< 68 86328 3 wifly-GSX-400
<
< 166 Free, Boot=68, Backup=34
< <4.00>
> load user
< load user
< AOK
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.00>
> set w l 5
< set w l 5
< AOK
< <4.00>
> set w s �MOTOROLA-C7B82
< set w s ?MOTOROLA-C7B82
< AOK
< <4.00>
> set w p a4a2d35a44912fefbeef
< set w p a4a2d35a44912fefbeef
< AOK
< <4.00>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.00>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> reboot
< reboot
> $$$
< CMD
> show n
< show n
< SSid=?MOTOROLA-C7B82
< Chan=6
< Assoc=FAIL
< Rate=12, 24Mb
< Auth=FAIL
< Mode=NONE
< DHCP=FAIL
< Boot=0
< Time=OK
< Links=0
< <4.00>
> get i
< get i
< IF=DOWN
< DHCP=ON
< IP=10.1.10.20:2000
< NM=255.255.255.0
< GW=10.1.10.1
< HOST=198.171.134.6:80
< PROTO=TCP,
< MTU=1524
< FLAGS=0x6
< TCPMODE=0x0
< BACKUP=0.0.0.0
< <4.00>
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Your Reef Angel Wifi Attachment is now configured with the settings provided.
---------------------------------------------------------------------
If the blue LED is still blinking, it means that the Reef Angel Wifi Attachment could not connect to your wifi network.
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ftp u
< ftp u
< <4.00>
< FTP connecting to 198.175.253.161
< FTP timeout=2
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> factory RESET
< factory RESET
< Set Factory Defaults
> reboot
< <4.00>
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Factory Settings Restored
---------------------------------------------------------------------
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ftp u
< ftp u
< <4.00>
< FTP connecting to 198.175.253.161
< FTP timeout=2
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again.
Removing connection to COM3
Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------
Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 78524 3 WiFly_GSX-2.32
< 22 44704 3 wps_app
< 33 -1 10 config
< 34 78524 3 WiFly_GSX-2.32
< 54 49072 3 wps_app
< 67 -1 10 user
< 68 86328 3 wifly-GSX-400
<
< 166 Free, Boot=68, Backup=34
< <4.00>
> load user
< load user
< AOK
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.00>
> set w l 5
< set w l 5
< AOK
< <4.00>
> set w s �MOTOROLA-C7B82
< set w s ?MOTOROLA-C7B82
< AOK
< <4.00>
> set w p a4a2d35a44912fefbeef
< set w p a4a2d35a44912fefbeef
< AOK
< <4.00>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.00>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.00>
> save
< save
< Storing in config
< *BAD CONFIG*
< <4.00>
> reboot
< reboot
> $$$
< CMD
> show n
< show n
< SSid=?MOTOROLA-C7B82
< Chan=6
< Assoc=FAIL
< Rate=12, 24Mb
< Auth=FAIL
< Mode=NONE
< DHCP=FAIL
< Boot=0
< Time=OK
< Links=0
< <4.00>
> get i
< get i
< IF=DOWN
< DHCP=ON
< IP=10.1.10.20:2000
< NM=255.255.255.0
< GW=10.1.10.1
< HOST=198.171.134.6:80
< PROTO=TCP,
< MTU=1524
< FLAGS=0x6
< TCPMODE=0x0
< BACKUP=0.0.0.0
< <4.00>
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Your Reef Angel Wifi Attachment is now configured with the settings provided.
---------------------------------------------------------------------
If the blue LED is still blinking, it means that the Reef Angel Wifi Attachment could not connect to your wifi network.
Re: wifi and setup issues
No idea what I all just posted there but its not connecting also it wont let me update the firmware which I figured would need updating
Re: wifi and setup issues
Something is not right with the config file.
Try doing this:
http://forum.reefangel.com/viewtopic.php?f=3&t=4601
Try doing this:
http://forum.reefangel.com/viewtopic.php?f=3&t=4601
Roberto.
Re: wifi and setup issues
Also is there updates I should do to the controller software? Or can I do that after I get Wifi going to it?
Re: wifi and setup issues
rimai wrote:Something is not right with the config file.
Try doing this:
http://forum.reefangel.com/viewtopic.php?f=3&t=4601
Really not sure if I'm that computer literate for this process.
Re: wifi and setup issues
heathd wrote:rimai wrote:Something is not right with the config file.
Try doing this:
http://forum.reefangel.com/viewtopic.php?f=3&t=4601
Really not sure if I'm that computer literate for this process.
Yah been trying for 2 hrs to make that tera thing work no luck. Idk
Re: wifi and setup issues
Idk what I'm doing wrong I downloaded everything. I think I put the right info into the macro. When I open that program it asks some stuff and I'm screwing that up I think.rimai wrote:Which step are you getting hung up at?
Re: wifi and setup issues
Okay I got it going but now the portal function here on the web site keeps saying unreachable address. updated my profile so it has the right ip address and port. any ideas?
Re: wifi and setup issues
So now I'm having trouble with the portal! It's a fight man. Lol. Anyways so I set my router ip address and portal so it stays and the portal is open. Still can't use the portal. 100%. Wanna be able to set time and update my software. Any ideas what's wrong? Modem support was looking for a subnet mask. Or something. Also the portal page keeps reseting my ip address when I try to connect so I have to go back into my profile every time.
Re: wifi and setup issues
Don't worry about changing the ip address. It is most likely auto correcting it for you.
You are probably trying to enter the local router ip address and it is not the one you want to use.
You want to use your outside ip address that is given to you by your internet provider.
You can see which one it is by visiting http://www.whatismyip.com/ from any computer inside your home network.
Your problem is that you must setup port forwarding in your router. Routers are set to block all access and assume they are all harmful.
You are probably trying to enter the local router ip address and it is not the one you want to use.
You want to use your outside ip address that is given to you by your internet provider.
You can see which one it is by visiting http://www.whatismyip.com/ from any computer inside your home network.
Your problem is that you must setup port forwarding in your router. Routers are set to block all access and assume they are all harmful.
Roberto.
Re: wifi and setup issues
Pretty sure I did that.i spent an hour on the phone with Motorola setting up the port stuff. Idk he thought there should be no issues. My dang firewall is even turned off still nothing.
Re: wifi and setup issues
Try your port forwarding here:
http://www.yougetsignal.com/tools/open-ports/
Make sure to use port 2000
http://www.yougetsignal.com/tools/open-ports/
Make sure to use port 2000
Roberto.
-
howaboutme
- Posts: 245
- Joined: Tue Jan 28, 2014 11:10 am
- Location: Northern VA
Re: wifi and setup issues
See if this website can help you.
http://portforward.com/english/routers/port_forwarding/
choose your router and follow the directions.
http://portforward.com/english/routers/port_forwarding/
choose your router and follow the directions.
Jack
Re: wifi and setup issues
Okay I'll mess with it later but what your saying is I need to open the incoming ip address and port? The one I have on the portal is showing me. I was messing with the other one.
-
howaboutme
- Posts: 245
- Joined: Tue Jan 28, 2014 11:10 am
- Location: Northern VA
Re: wifi and setup issues
You're being distracted by the splash page after you click on your router brand. There is a "close" "x" at the top. Just carefully run through the site. It is FREE. Take your time so you totally comprehend everything.heathd wrote:Looks like that link would be great. Except 30 bucks! Grrrr
Jack
Re: wifi and setup issues
Ah thanks looking at it with my phone. Didn't notice thanks. I'll try later.
Re: wifi and setup issues
yahh I went through that again I had done it last night its still not letting me in. is there something else I need on in a Motorola modem with Mediacom cable internet?
Re: wifi and setup issues
I paid 30 bucks for support with my modem did what they told me still not working. Port closed.
-
howaboutme
- Posts: 245
- Joined: Tue Jan 28, 2014 11:10 am
- Location: Northern VA
Re: wifi and setup issues
Can you tell us your exact Motorola modem model #? When I have time, I'll look it up and see if I can walk you through it. Or perhaps someone else w/ the same modem can too.
By the way, do you have a modem only or a modem/router? Also, do you have 2 of them wired together or just the one that came from your internet company?
By the way, do you have a modem only or a modem/router? Also, do you have 2 of them wired together or just the one that came from your internet company?
Jack
Re: wifi and setup issues
It's just one combo modem router with cable Internet. Btw thanks for taking time to try and help here. I've been happy with everything so far just trying to get this last step done here has kicked my ass.
-
howaboutme
- Posts: 245
- Joined: Tue Jan 28, 2014 11:10 am
- Location: Northern VA
Re: wifi and setup issues
I just went to that website that I posted. I looked for your router and the instructions. One thing that I don't remember needing to do is create a static IP address. (I went to the instructions for my router and it suggests the same but I am pretty sure I didn't do it.)
So...for forwarding, I used as an example "Apache" since RA will not be in the list. The concept is the same. The only difference is that RA uses port 2000.
Try that and see what happens. It would help to post what your ISP or Motorola suggested you do for port forwarding too if the above doesn't work. Good luck!
So...for forwarding, I used as an example "Apache" since RA will not be in the list. The concept is the same. The only difference is that RA uses port 2000.
Try that and see what happens. It would help to post what your ISP or Motorola suggested you do for port forwarding too if the above doesn't work. Good luck!
Jack