Wifi attachment commands
Re: Wifi attachment commands
It was already there... It didn't have the min, max and user define, but was there. I added the other ones. Check if it scales now.
On my android, it scales on height, not on width.
On my android, it scales on height, not on width.
Roberto.
Re: Wifi attachment commands
No change...
I am getting a lot of unable to refresh data and I know everything is working. My other software is loading data ok...
I am getting a lot of unable to refresh data and I know everything is working. My other software is loading data ok...
Re: Wifi attachment commands
Actually it may be worse now.... I cant scale it all now on safari. Not sure what it was like before. I was using chrome in previous tests. Also data loading fine in safari so maybe a chrome issue..
Re: Wifi attachment commands
Chrome is not scaling now either ...maybe it was cached..
Re: Wifi attachment commands
I think it is because of user-scalable=0 that you posted.
I reverted back.
I reverted back.
Roberto.
Re: Wifi attachment commands
I'll have to see if i can make a dev copy of your js file and see what i can do...
Re: Wifi attachment commands
This is what I got:
Viewport argument value "device-width;" for key "width" is invalid, and has been ignored. Note that ';' is not a separator in viewport values. The list should be comma-separated.
My original code had comma and when you posted yours, I changed to semi-colon.
So, I updated once again back with a comma. Can you see if it does it now?
Viewport argument value "device-width;" for key "width" is invalid, and has been ignored. Note that ';' is not a separator in viewport values. The list should be comma-separated.
My original code had comma and when you posted yours, I changed to semi-colon.
So, I updated once again back with a comma. Can you see if it does it now?
Roberto.
Re: Wifi attachment commands
Perfect in safari. Still have issues with Chrome. It doesnt get any data and doesn't default to the right width. Safari is perfect.
Re: Wifi attachment commands
These are reversed in practice... When I set the po14,0 it changed the RFG and when I set po15,0 it changed RFB.14-Radion - Blue Channel
15-Radion - Green Channel
A bit off topic but the reason for this discovery... something is changing my RFB and RFI to 100 and I can't figure it out. I have nothing in my code that references the Radion's at all, except that I'm using the Custom mode for the Vortech... I did have 100 in Mem_B_RadionRadionSlopeEndB and Mem_B_RadionRadionSlopeEndI but I corrected that. Then I overrode the channels to 0 and put back to default and it went right back to 100. It's happened a few times and not sure what's triggering it. Any thoughts?
Re: Wifi attachment commands
Thanks!!
What you are getting is the intended result. It was a mistake on that post. I corrected it.
It has to be something within your code.
It is not the override as you can see it in here: http://forum.reefangel.com/status/chart ... filter=rfb
Can you open a new thread?
What you are getting is the intended result. It was a mistake on that post. I corrected it.
It has to be something within your code.
It is not the override as you can see it in here: http://forum.reefangel.com/status/chart ... filter=rfb
Can you open a new thread?
Roberto.
Re: Wifi attachment commands
I'll start a new thread... just the typo was noticed when I tried to see if the override would help reset it.
Re: Wifi attachment commands
what is the usage of the /cal command? can it be used to trigger the calibration modes?
Re: Wifi attachment commands
awesome. thanksrimai wrote:Yes, I updated the OP
Re: Wifi attachment commands
There is no way to read/write a dword (i.e. InternalMemory.read_dword() / InternalMemory.write_dword() )
Need to ad a /md
Need to ad a /md
Re: Wifi attachment commands
Can you add a ticket on github?
Sent from my SPH-L710 using Tapatalk
Sent from my SPH-L710 using Tapatalk
Roberto.
Re: Wifi attachment commands
Yeah, I'll add this and need to add HighATOChannel to DCPump
Re: Wifi attachment commands
I have the same question, is there a schema for the data that /sr or /sa will return? The answer to genuflect is begged!!
Re: Wifi attachment commands
If you want to know what the schema looks like, then you need to view the code. It's located in the RA_Wifi/RA_Wifi.cpp file. Here's a link to the github location of the file:Hamid2 wrote:I have the same question, is there a schema for the data that /sr or /sa will return? The answer to genuflect is begged!!
https://github.com/reefangel/Libraries/ ... A_Wifi.cpp
Around line 300, there will be a line that says "case REQ_R_STATUS:"
That section shows the the XML code that is generated by those 2 commands.
Re: Wifi attachment commands
Any way to add a command to clear a bus lock flag? If it's possible I'll open an issue.
Re: Wifi attachment commands
I could be missing something obvious.. but when I call the waterchange mode from the wifi... how do I take the RA out of WC mode? Do I make the same call again to toggle it?
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Re: Wifi attachment commands
Of course looking at this now - it makes perfect sense. I'm going to blame being tired.
Do you know if there's a way to check if WC or Feed mode are already active?
Do you know if there's a way to check if WC or Feed mode are already active?
Re: Wifi attachment commands
Yes. The SF flag is an 8 bit representation of different modes.
At the moment, we only use the first 3 bits.
At the moment, we only use the first 3 bits.
Code: Select all
// Status Flag Bits
#define LightsOnFlag 0
#define FeedingFlag 1
#define WaterChangeFlag 2
Roberto.