- Code: Select all
#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <DCPump.h>
#include <PAR.h>
#include <ReefAngel.h>
////// Place global variable code below here
////// Place global variable code above here
void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
ReefAngel.Use2014Screen(); // Let's use 2014 Screen
ReefAngel.AddSalinityExpansion(); // Salinity Expansion Module
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = 0;
ReefAngel.FeedingModePortsE[0] = 0;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = Port3Bit;
ReefAngel.WaterChangePortsE[0] = 0;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = 0;
ReefAngel.LightsOnPortsE[0] = 0;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = Port7Bit;
ReefAngel.OverheatShutoffPortsE[0] = 0;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T3_PROBE;
ReefAngel.OverheatProbe = T3_PROBE;
// Ports that are always on
ReefAngel.Relay.On( Port4 );
ReefAngel.Relay.On( Port6 );
ReefAngel.Relay.On( Box1_Port3 );
ReefAngel.Relay.On( Box1_Port4 );
ReefAngel.Relay.On( Box1_Port7 );
ReefAngel.Relay.On( Box1_Port8 );
////// Place additional initialization code below here
////// Place additional initialization code above here
}
void loop()
{
ReefAngel.StandardATO( Port3 );
ReefAngel.StandardHeater( Port7 );
ReefAngel.MoonLights( Box1_Port6 );
ReefAngel.PWM.Channel0PWMSlope();
ReefAngel.PWM.Channel1PWMSlope();
ReefAngel.PWM.Channel2PWMSlope();
ReefAngel.PWM.Channel3PWMSlope();
ReefAngel.PWM.Channel4PWMSlope();
ReefAngel.PWM.Channel5PWMSlope();
////// Place your custom code below here
////// Place your custom code above here
// This should always be the last line
ReefAngel.Portal( "jjdezek" );
ReefAngel.ShowInterface();
}
heater not turning off
3 posts
• Page 1 of 1
now that I have reprogrammed my controller after dealing with my lights issue my heater doesn't shut off when it gets above the desired temp. ive tried setting it to all three temp probes and none of them turn the heater off. I set the code up with the internal memory. here is the code I have loaded.
|
|
Hard to tell with internal memory code.
What values do you have? Did you try hard coding it? Roberto.
|
|
I have it the same as I had in the past. Turn on at 77.0 and turn off at 77.1. Since I redid the code it hasn’t been working right. Like right now my tank is at 77.3 and the heater is on.
|
|
3 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 4 guests