Reef Angel Forum

Community discussion about Reef Angel Controllers and reefing related subjects
https://forum.reefangel.com/

PaulTurner911 Code

https://forum.reefangel.com/viewtopic.php?t=3419

Page 3 of 9

Re: PaulTurner911 Code

Posted: Thu Jul 25, 2013 6:06 am
by Paulturner911
lnevo wrote:
lnevo wrote:
Changed extension of feeding mode to 15 minutes so total duration is 30. Feel free to make the 900 back to 1800.

Fixed the timer issue you had as well...sorry bout that one.
Force night mode to Constant instead of whatever is default mode (NTM was today's mode.)
Ok, so we changed to 1800 to 900 but never changed the comment line?

Re: PaulTurner911 Code

Posted: Thu Jul 25, 2013 7:51 am
by lnevo
Correct. Was trying to match up with what you were trying to do. I didn't change the comments.

Re: PaulTurner911 Code

Posted: Thu Jul 25, 2013 7:55 am
by Paulturner911
Thanks Bud!!!!

Re: PaulTurner911 Code

Posted: Tue Jul 30, 2013 6:42 pm
by Paulturner911
Any chance you had time to revise the code and implement the boolean?

Re: PaulTurner911 Code

Posted: Tue Jul 30, 2013 7:28 pm
by lnevo
Sorry i haven't yet, it fell off my radar. Give me a bit still, been super busy and tomorrow I am picking up my new mandarin! Nice and fat and trained to eat frozen! So I'll be busy holding the fish bag on the train home :)

Re: PaulTurner911 Code

Posted: Wed Jul 31, 2013 7:09 am
by Paulturner911
Thanks! No rush by any means.
I guess Ive been lucky, my mandrin eats ANYTHING!!
TRAIN?!? Where do you live?

Re: PaulTurner911 Code

Posted: Wed Jul 31, 2013 9:36 am
by lnevo
Long Island Rail Road to manhattan every day. Fun. Not.

Re: PaulTurner911 Code

Posted: Thu Aug 01, 2013 3:04 pm
by lnevo
Ok, so this should do...

0:00 Feeding Mode Start (all pumps off)
0:15 Smart_NTM
0:30 Feeding Mode End (return pump on)
1:15 Smart_NTM end / Resume previous mode

Good Luck, keep me posted.

Code: Select all

// Set timer when in feeding mode
static boolean feedingStarted;
static unsigned long feeding;
if (ReefAngel.DisplayedMenu==FEEDING_MODE && !feedingStarted) {
    feedingStarted=true;
    feeding = now();
} else {
  feedingStarted=false;
}

// Feeding Mode is 30 minutes
if (now()-feeding<=900) { 
  // First 15 minutes after feeding mode. Pump is off
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Speed=0;
} else if (now()-feeding<=(900+3600)) { 
  // NTM after 15 minutes for the next 60 minutes
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Mode=NutrientTransport;
  ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Resume previous speed

Re: PaulTurner911 Code

Posted: Thu Aug 01, 2013 3:19 pm
by Paulturner911
Im getting an error 'redeclaration of long unsinged in feeding.

Here is my complete code

Code: Select all

#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <DCPump.h>
#include <ReefAngel.h>

////// Place global variable code below here


////// Place global variable code above here


void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = Port1Bit | Port2Bit | Port7Bit | Port8Bit;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = Port1Bit | Port2Bit | Port7Bit | Port8Bit;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = Port2Bit | Port3Bit | Port7Bit | Port8Bit;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = Port3Bit | Port7Bit | Port8Bit;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;

// Feeeding and Water Change mode speed
ReefAngel.DCPump.FeedingSpeed=0;
ReefAngel.DCPump.WaterChangeSpeed=0;


// Ports that are always on

////// Place additional initialization code below here


////// Place additional initialization code above here
}

void loop()
{
ReefAngel.DayLights( Port1 ); // Return Pump
ReefAngel.StandardFan( Port2 ); // Canopy Fans
ReefAngel.ActinicLights( Port3 ); // Actinic LEDS
//Port4 Kalk/ATO
//Port5 Kalk Stir
//Port 6 NOT USED (Possibly Skimmer)
ReefAngel.DayLights( Port7 ); // MH 1
ReefAngel.DayLights( Port8 ); //MH 2
//Moonlight Phase 9pm-10am (CH4-CH5)
if ( (hour() >=10) && (hour() <21) ) 
ReefAngel.PWM.SetChannel( 4,(0) );
else 
ReefAngel.PWM.SetChannel( 4, MoonPhase() );
if ( (hour() >=10) && (hour() <21) ) 
ReefAngel.PWM.SetChannel( 5,(0) );
else
ReefAngel.PWM.SetChannel( 5, MoonPhase() );

//Over Flow Protection
if (ReefAngel.HighATO.IsActive())
ReefAngel.Relay.On(Port1);
else
ReefAngel.Relay.Off(Port1);

//ATO Protection
if (ReefAngel.LowATO.IsActive())
ReefAngel.Relay.On(Port4);
else
ReefAngel.Relay.Off(Port4);

//Kalk Dose 60sec @ 11pm-12pm (every 15min)
if (hour() >=23 || hour() < 12)
ReefAngel.Relay.Set(Port4, now()%900<60);
else
ReefAngel.Relay.Off(Port4);

//Kalk Stir 12pm-1pm
if (hour() >=12 & hour() < 13)
ReefAngel.Relay.On(Port5);
else
ReefAngel.Relay.Off(Port5);


ReefAngel.DCPump.UseMemory = true;
ReefAngel.DCPump.DaylightChannel = Sync;
////// Place your custom code below here

///// Place your custom code below here

// Add random mode if we set to Mode to Custom in portal
static int rmode;
static boolean changeMode=true;

// These are the modes we can cycle through. You can add more and even repeat...
byte modes[] = { ReefCrest, TidalSwell, ShortPulse, NutrientTransport };

if (now()%SECS_PER_DAY==0 || changeMode==true) { // Change at midnight or if controller rebooted
rmode=random(100)%sizeof(modes); // Change the mode once per day to pick from our array
changeMode=false;
}

// Set timer when in feeding mode
static unsigned long feeding;
if (ReefAngel.DisplayedMenu==FEEDING_MODE) {
feeding = now();
}

// Set timer when in feeding mode
static boolean feedingStarted;
static unsigned long feeding;
if (ReefAngel.DisplayedMenu==FEEDING_MODE && !feedingStarted) {
    feedingStarted=true;
    feeding = now();
} else {
  feedingStarted=false;
}

// Feeding Mode is 30 minutes
if (now()-feeding<=900) { 
  // First 15 minutes after feeding mode. Pump is off
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Speed=0;
} else if (now()-feeding<=(900+3600)) { 
  // NTM after 15 minutes for the next 60 minutes
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Mode=NutrientTransport;
  ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Resume previous speed
  // Night mode (go to 30%)
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Mode=Constant;
  ReefAngel.DCPump.Speed=30;
} else if (InternalMemory.DCPumpMode_read()==11) { 
  // Custom Mode and nothing else going on
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Mode=modes[rmode];  // Put the mode to the random mode :)
  ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Set speed from portal
} else {
  ReefAngel.DCPump.UseMemory=true; // Will reset all values from memory
}

////// Place your custom code above here

// This should always be the last line
ReefAngel.Portal( "paulturner911" );
ReefAngel.ShowInterface();
}

void DrawCustomMain()
{
int x,y;
char text[10];
// Dimming Expansion
x = 15;
y = 2;
for ( int a=0;a<6;a++ )
{
if ( a>2 ) x = 75;
if ( a==3 ) y = 2;
ReefAngel.LCD.DrawText( COLOR_DARKGOLDENROD,DefaultBGColor,x,y,"Ch :" );
ReefAngel.LCD.DrawText( COLOR_DARKGOLDENROD,DefaultBGColor,x+12,y,a );
ReefAngel.LCD.DrawText( COLOR_DARKGOLDENROD,DefaultBGColor,x+24,y,ReefAngel.PWM.GetChannelValue(a) );
y += 10;
}
pingSerial();

// Parameters
#if defined DisplayLEDPWM && ! defined RemoveAllLights
ReefAngel.LCD.DrawMonitor( 15, 43, ReefAngel.Params,
ReefAngel.PWM.GetDaylightValue(), ReefAngel.PWM.GetActinicValue() );
#else // defined DisplayLEDPWM && ! defined RemoveAllLights
ReefAngel.LCD.DrawMonitor( 15, 43, ReefAngel.Params );
#endif // defined DisplayLEDPWM && ! defined RemoveAllLights
pingSerial();

// Main Relay Box
byte TempRelay = ReefAngel.Relay.RelayData;
TempRelay &= ReefAngel.Relay.RelayMaskOff;
TempRelay |= ReefAngel.Relay.RelayMaskOn;
ReefAngel.LCD.DrawOutletBox( 12, 84, TempRelay );
pingSerial();

// Date and Time
ReefAngel.LCD.DrawDate( 6, 122 );
pingSerial();
}

void DrawCustomGraph()
{
}

Re: PaulTurner911 Code

Posted: Thu Aug 01, 2013 3:21 pm
by lnevo
You didn't delete this part...

// Set timer when in feeding mode
static unsigned long feeding;
if (ReefAngel.DisplayedMenu==FEEDING_MODE) {
feeding=now();
}

Re: PaulTurner911 Code

Posted: Sun Aug 11, 2013 4:46 pm
by Paulturner911
Somethings not right with the current code. The day after feedmode was activated the WP is at zero. Im guessing after NTM it never resumes our random custom mode. Also could you refresh me on the memory location of feedmode timer? Where could I find a list of all memory locations?

Re: PaulTurner911 Code

Posted: Sun Aug 11, 2013 4:49 pm
by lnevo
It's in the file in libraries/Globals/Globals.

Look for the string VarsStart.

Re: PaulTurner911 Code

Posted: Mon Aug 19, 2013 6:44 pm
by Paulturner911
Any chance you could revisit your logic on the feedmode? I've set the feedtime in the memloc to 900 and once that completes the return pump AND the wp turn. I'd like the wp to run NTM for a while before the returns kick on. Any help would be great.

Re: PaulTurner911 Code

Posted: Mon Aug 19, 2013 7:39 pm
by lnevo
Set the feed mode to however long you want them off. 900 is when ntm kicks on.

Re: PaulTurner911 Code

Posted: Mon Aug 19, 2013 7:42 pm
by Paulturner911
Tx!

Re: PaulTurner911 Code

Posted: Sun Sep 08, 2013 11:23 am
by Paulturner911
This doesn't seem to be the case. I've currently set the feedmode to 1800.... At the 900 mark nothing happens, and 0 all pumps turn on and run NTM.

Re: PaulTurner911 Code

Posted: Sun Sep 08, 2013 12:53 pm
by lnevo
Did you change 900 in your code at all? The code I posted above sets the speed to 0 only for the first 900 seconds after feeding mode started..then its NTM until 4500 seconds.

Can you set the feeding mode time longer than 1800 and tell me what happens at the 1800 mark?

What is port1 port2 port7 and port8?

Re: PaulTurner911 Code

Posted: Sun Sep 08, 2013 3:39 pm
by Paulturner911
I dont have an appropriate file reader to read globals/globals for memory locations.

Ive set the feedmode to 1860 and at 1800 nothing happens. Im assuming that at 960 the NTM should activate, it doesnt.

Port1- RETURN PUMP
2-FANS
7-MH
8-MH

these all turn off in feed mode


this is my code:

// Feeding Mode is 30 minutes
if (now()-feeding<=900) {
// First 15 minutes after feeding mode. Pump is off
ReefAngel.DCPump.UseMemory=false;
ReefAngel.DCPump.Speed=0;
} else if (now()-feeding<=(900+3600)) {
// NTM after 15 minutes for the next 60 minutes
ReefAngel.DCPump.UseMemory=false;
ReefAngel.DCPump.Mode=NutrientTransport;
ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Resume previous speed
// Night mode (go to 30%)
ReefAngel.DCPump.UseMemory=false;
ReefAngel.DCPump.Mode=Constant;
ReefAngel.DCPump.Speed=30;
} else if (InternalMemory.DCPumpMode_read()==11) {
// Custom Mode and nothing else going on
ReefAngel.DCPump.UseMemory=false;
ReefAngel.DCPump.Mode=modes[rmode]; // Put the mode to the random mode :)
ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Set speed from portal
} else {
ReefAngel.DCPump.UseMemory=true; // Will reset all values from memory
}

////// Place your custom code above here

Re: PaulTurner911 Code

Posted: Sun Sep 08, 2013 4:22 pm
by lnevo
Im baffled here too...between you and sacohen i feel like im losing my mind...

Roberto binder anyone need a second set of eyes...speed and mode should be reset at 901 seconds..

Re: PaulTurner911 Code

Posted: Wed Sep 11, 2013 6:49 pm
by Paulturner911
Anyone?

Re: PaulTurner911 Code

Posted: Wed Sep 11, 2013 6:54 pm
by rimai
Sorry... what is exactly that you want?

Sent from my SPH-L710 using Tapatalk 4

Re: PaulTurner911 Code

Posted: Wed Sep 11, 2013 7:39 pm
by lnevo
I know what the problem is. I'll post something tomorrow. Can you post your full code again.

Re: PaulTurner911 Code

Posted: Thu Sep 12, 2013 2:55 am
by lnevo
Try this:

Code: Select all

#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <DCPump.h>
#include <ReefAngel.h>

////// Place global variable code below here


////// Place global variable code above here


void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = Port1Bit | Port2Bit | Port7Bit | Port8Bit;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = Port1Bit | Port2Bit | Port7Bit | Port8Bit;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = Port2Bit | Port3Bit | Port7Bit | Port8Bit;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = Port3Bit | Port7Bit | Port8Bit;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;

// Feeeding and Water Change mode speed
ReefAngel.DCPump.FeedingSpeed=0;
ReefAngel.DCPump.WaterChangeSpeed=0;


// Ports that are always on

////// Place additional initialization code below here


////// Place additional initialization code above here
}

void loop()
{
ReefAngel.DayLights( Port1 ); // Return Pump
ReefAngel.StandardFan( Port2 ); // Canopy Fans
ReefAngel.ActinicLights( Port3 ); // Actinic LEDS
//Port4 Kalk/ATO
//Port5 Kalk Stir
//Port 6 NOT USED (Possibly Skimmer)
ReefAngel.DayLights( Port7 ); // MH 1
ReefAngel.DayLights( Port8 ); //MH 2
//Moonlight Phase 9pm-10am (CH4-CH5)
if ( (hour() >=10) && (hour() <21) ) 
ReefAngel.PWM.SetChannel( 4,(0) );
else 
ReefAngel.PWM.SetChannel( 4, MoonPhase() );
if ( (hour() >=10) && (hour() <21) ) 
ReefAngel.PWM.SetChannel( 5,(0) );
else
ReefAngel.PWM.SetChannel( 5, MoonPhase() );

//Over Flow Protection
if (ReefAngel.HighATO.IsActive())
ReefAngel.Relay.On(Port1);
else
ReefAngel.Relay.Off(Port1);

//ATO Protection
if (ReefAngel.LowATO.IsActive())
ReefAngel.Relay.On(Port4);
else
ReefAngel.Relay.Off(Port4);

//Kalk Dose 60sec @ 11pm-12pm (every 15min)
if (hour() >=23 || hour() < 12)
ReefAngel.Relay.Set(Port4, now()%900<60);
else
ReefAngel.Relay.Off(Port4);

//Kalk Stir 12pm-1pm
if (hour() >=12 & hour() < 13)
ReefAngel.Relay.On(Port5);
else
ReefAngel.Relay.Off(Port5);


ReefAngel.DCPump.UseMemory = true;
ReefAngel.DCPump.DaylightChannel = Sync;
////// Place your custom code below here

///// Place your custom code below here

// Add random mode if we set to Mode to Custom in portal
static int rmode;
static boolean changeMode=true;

// These are the modes we can cycle through. You can add more and even repeat...
byte modes[] = { ReefCrest, TidalSwell, ShortPulse, NutrientTransport };

if (now()%SECS_PER_DAY==0 || changeMode==true) { // Change at midnight or if controller rebooted
rmode=random(100)%sizeof(modes); // Change the mode once per day to pick from our array
changeMode=false;
}

// Set timer when in feeding mode
static unsigned long feeding;
static boolean startFeeding=false;
if (ReefAngel.DisplayedMenu==FEEDING_MODE && startFeeding) {
feeding = now();
startFeeding=false;
} else {
startFeeding = true;
}

// Set timer when in feeding mode
static boolean feedingStarted;
static unsigned long feeding;
if (ReefAngel.DisplayedMenu==FEEDING_MODE && !feedingStarted) {
    feedingStarted=true;
    feeding = now();
} else {
  feedingStarted=false;
}

// Feeding Mode is 30 minutes
if (now()-feeding<=900) { 
  // First 15 minutes after feeding mode. Pump is off
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Speed=0;
} else if (now()-feeding<=900+3600)) { 
  // NTM after 15 minutes for the next 60 minutes
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Mode=NutrientTransport;
  ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Resume previous speed
  // Night mode (go to 30%)
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Mode=Constant;
  ReefAngel.DCPump.Speed=30;
} else if (InternalMemory.DCPumpMode_read()==11) { 
  // Custom Mode and nothing else going on
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Mode=modes[rmode];  // Put the mode to the random mode :)
  ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Set speed from portal
} else {
  ReefAngel.DCPump.UseMemory=true; // Will reset all values from memory
}

////// Place your custom code above here

// This should always be the last line
ReefAngel.Portal( "paulturner911" );
ReefAngel.ShowInterface();
}

void DrawCustomMain()
{
int x,y;
char text[10];
// Dimming Expansion
x = 15;
y = 2;
for ( int a=0;a<6;a++ )
{
if ( a>2 ) x = 75;
if ( a==3 ) y = 2;
ReefAngel.LCD.DrawText( COLOR_DARKGOLDENROD,DefaultBGColor,x,y,"Ch :" );
ReefAngel.LCD.DrawText( COLOR_DARKGOLDENROD,DefaultBGColor,x+12,y,a );
ReefAngel.LCD.DrawText( COLOR_DARKGOLDENROD,DefaultBGColor,x+24,y,ReefAngel.PWM.GetChannelValue(a) );
y += 10;
}
pingSerial();

// Parameters
#if defined DisplayLEDPWM && ! defined RemoveAllLights
ReefAngel.LCD.DrawMonitor( 15, 43, ReefAngel.Params,
ReefAngel.PWM.GetDaylightValue(), ReefAngel.PWM.GetActinicValue() );
#else // defined DisplayLEDPWM && ! defined RemoveAllLights
ReefAngel.LCD.DrawMonitor( 15, 43, ReefAngel.Params );
#endif // defined DisplayLEDPWM && ! defined RemoveAllLights
pingSerial();

// Main Relay Box
byte TempRelay = ReefAngel.Relay.RelayData;
TempRelay &= ReefAngel.Relay.RelayMaskOff;
TempRelay |= ReefAngel.Relay.RelayMaskOn;
ReefAngel.LCD.DrawOutletBox( 12, 84, TempRelay );
pingSerial();

// Date and Time
ReefAngel.LCD.DrawDate( 6, 122 );
pingSerial();
}

void DrawCustomGraph()
{
}
[/quote]

This was the section I modified

Code: Select all


// Set timer when in feeding mode
static unsigned long feeding;
static boolean startFeeding=false;
if (ReefAngel.DisplayedMenu==FEEDING_MODE && startFeeding) {
feeding = now();
startFeeding=false;
} else {
startFeeding = true;
}

Re: PaulTurner911 Code

Posted: Thu Sep 12, 2013 12:21 pm
by Paulturner911
Thanks Lee, Ill let you know in the next few days. I really appreciate it.

Re: PaulTurner911 Code

Posted: Thu Sep 12, 2013 4:07 pm
by Paulturner911
No bueno. Ive run the feedmode 3 times set at 1200 and the oven timer set at 15min. the NTM mode does not kick in at 901 (299 in countdown on LCD) Infact, the WP is not calling anymode untill I power cycle the unit, then it calls NTM. Any help would be great.

Here is my current code:

Code: Select all

// This must be the first line
ReefAngel.Init(); //Initialize controller
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = Port1Bit | Port2Bit | Port7Bit | Port8Bit;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = Port1Bit | Port2Bit | Port7Bit | Port8Bit;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = Port2Bit | Port3Bit | Port7Bit | Port8Bit;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = Port3Bit | Port7Bit | Port8Bit;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;

// Feeeding and Water Change mode speed
ReefAngel.DCPump.FeedingSpeed=0;
ReefAngel.DCPump.WaterChangeSpeed=0;


// Ports that are always on

////// Place additional initialization code below here


////// Place additional initialization code above here
}

void loop()
{
ReefAngel.DayLights( Port1 ); // Return Pump
ReefAngel.StandardFan( Port2 ); // Canopy Fans
ReefAngel.ActinicLights( Port3 ); // Actinic LEDS
//Port4 Kalk/ATO
//Port5 Kalk Stir
//Port 6 NOT USED (Possibly Skimmer)
ReefAngel.DayLights( Port7 ); // MH 1
ReefAngel.DayLights( Port8 ); //MH 2
//Moonlight Phase 9pm-10am (CH4-CH5)
if ( (hour() >=10) && (hour() <21) ) 
ReefAngel.PWM.SetChannel( 4,(0) );
else 
ReefAngel.PWM.SetChannel( 4, MoonPhase() );
if ( (hour() >=10) && (hour() <21) ) 
ReefAngel.PWM.SetChannel( 5,(0) );
else
ReefAngel.PWM.SetChannel( 5, MoonPhase() );

//Over Flow Protection
if (ReefAngel.HighATO.IsActive())
ReefAngel.Relay.On(Port1);
else
ReefAngel.Relay.Off(Port1);

//ATO Protection
if (ReefAngel.LowATO.IsActive())
ReefAngel.Relay.On(Port4);
else
ReefAngel.Relay.Off(Port4);

//Kalk Dose 60sec @ 11pm-12pm (every 15min)
if (hour() >=23 || hour() < 12)
ReefAngel.Relay.Set(Port4, now()%900<60);
else
ReefAngel.Relay.Off(Port4);

//Kalk Stir 12pm-1pm
if (hour() >=12 & hour() < 13)
ReefAngel.Relay.On(Port5);
else
ReefAngel.Relay.Off(Port5);


ReefAngel.DCPump.UseMemory = true;
ReefAngel.DCPump.DaylightChannel = Sync;
////// Place your custom code below here

///// Place your custom code below here

// Add random mode if we set to Mode to Custom in portal
static int rmode;
static boolean changeMode=true;

// These are the modes we can cycle through. You can add more and even repeat...
byte modes[] = { ReefCrest, TidalSwell, ShortPulse, NutrientTransport };

if (now()%SECS_PER_DAY==0 || changeMode==true) { // Change at midnight or if controller rebooted
rmode=random(100)%sizeof(modes); // Change the mode once per day to pick from our array
changeMode=false;
}


// Set timer when in feeding mode
static unsigned long feeding;
static boolean startFeeding=false;
if (ReefAngel.DisplayedMenu==FEEDING_MODE && startFeeding) {
feeding = now();
startFeeding=false;
} else {
startFeeding = true;
}
// Feeding Mode is 30 minutes
if (now()-feeding<=900) { 
  // First 15 minutes after feeding mode. Pump is off
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Speed=0;
} else if (now()-feeding<=(900+3600)) { 
  // NTM after 15 minutes for the next 60 minutes
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Mode=NutrientTransport;
  ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Resume previous speed
  // Night mode (go to 30%)
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Mode=Constant;
  ReefAngel.DCPump.Speed=30;
} else if (InternalMemory.DCPumpMode_read()==11) { 
  // Custom Mode and nothing else going on
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Mode=modes[rmode];  // Put the mode to the random mode :)
  ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Set speed from portal
} else {
  ReefAngel.DCPump.UseMemory=true; // Will reset all values from memory
}

////// Place your custom code above here

Re: PaulTurner911 Code

Posted: Thu Sep 12, 2013 4:22 pm
by lnevo
Grrr

Re: PaulTurner911 Code

Posted: Thu Sep 12, 2013 4:24 pm
by lnevo
Alright will look at it again soon...are u sure you poaded this code successfully...the full code not editing ur existing????

Re: PaulTurner911 Code

Posted: Thu Sep 12, 2013 4:42 pm
by lnevo
It looks also like you messed up the if block because i don't see the conditional to go into night mode...the ntm section goes right into night mode. Please also post your full code. Stop pasting blocks.

I believe the code worked but went into night mode instead. Post the full code ill fix it and we'll try again.

Re: PaulTurner911 Code

Posted: Fri Sep 13, 2013 5:29 am
by lnevo
Try this:

Code: Select all

#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <DCPump.h>
#include <ReefAngel.h>

////// Place global variable code below here


////// Place global variable code above here


void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = Port1Bit | Port2Bit | Port7Bit | Port8Bit;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = Port1Bit | Port2Bit | Port7Bit | Port8Bit;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = Port2Bit | Port3Bit | Port7Bit | Port8Bit;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = Port3Bit | Port7Bit | Port8Bit;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;

// Feeeding and Water Change mode speed
ReefAngel.DCPump.FeedingSpeed=0;
ReefAngel.DCPump.WaterChangeSpeed=0;


// Ports that are always on

////// Place additional initialization code below here


////// Place additional initialization code above here
}

void loop()
{
ReefAngel.DayLights( Port1 ); // Return Pump
ReefAngel.StandardFan( Port2 ); // Canopy Fans
ReefAngel.ActinicLights( Port3 ); // Actinic LEDS
//Port4 Kalk/ATO
//Port5 Kalk Stir
//Port 6 NOT USED (Possibly Skimmer)
ReefAngel.DayLights( Port7 ); // MH 1
ReefAngel.DayLights( Port8 ); //MH 2
//Moonlight Phase 9pm-10am (CH4-CH5)
if ( (hour() >=10) && (hour() <21) ) 
ReefAngel.PWM.SetChannel( 4,(0) );
else 
ReefAngel.PWM.SetChannel( 4, MoonPhase() );
if ( (hour() >=10) && (hour() <21) ) 
ReefAngel.PWM.SetChannel( 5,(0) );
else
ReefAngel.PWM.SetChannel( 5, MoonPhase() );

//Over Flow Protection
if (ReefAngel.HighATO.IsActive())
ReefAngel.Relay.On(Port1);
else
ReefAngel.Relay.Off(Port1);

//ATO Protection
if (ReefAngel.LowATO.IsActive())
ReefAngel.Relay.On(Port4);
else
ReefAngel.Relay.Off(Port4);

//Kalk Dose 60sec @ 11pm-12pm (every 15min)
if (hour() >=23 || hour() < 12)
ReefAngel.Relay.Set(Port4, now()%900<60);
else
ReefAngel.Relay.Off(Port4);

//Kalk Stir 12pm-1pm
if (hour() >=12 & hour() < 13)
ReefAngel.Relay.On(Port5);
else
ReefAngel.Relay.Off(Port5);


ReefAngel.DCPump.UseMemory = true;
ReefAngel.DCPump.DaylightChannel = Sync;
////// Place your custom code below here

///// Place your custom code below here

// Add random mode if we set to Mode to Custom in portal
static int rmode;
static boolean changeMode=true;

// These are the modes we can cycle through. You can add more and even repeat...
byte modes[] = { ReefCrest, TidalSwell, ShortPulse, NutrientTransport };

if (now()%SECS_PER_DAY==0 || changeMode==true) { // Change at midnight or if controller rebooted
rmode=random(100)%sizeof(modes); // Change the mode once per day to pick from our array
changeMode=false;
}

// Set timer when in feeding mode
static unsigned long feeding;
static boolean startFeeding=false;
if (ReefAngel.DisplayedMenu==FEEDING_MODE && startFeeding) {
feeding = now();
startFeeding=false;
} else {
startFeeding = true;
}

// Set timer when in feeding mode
static boolean feedingStarted;
static unsigned long feeding;
if (ReefAngel.DisplayedMenu==FEEDING_MODE && !feedingStarted) {
  feedingStarted=true;
  feeding = now();
} else {
  feedingStarted=false;
}

// Feeding Mode is 30 minutes
if (now()-feeding<=900) { 
  // First 15 minutes after feeding mode. Pump is off
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Speed=0;
} else if (now()-feeding<=900+3600)) { 
  // NTM after 15 minutes for the next 60 minutes
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Mode=NutrientTransport;
  ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Resume previous speed
  // Night mode (go to 30%)
} else if (now()%SECS_PER_DAY<30600 || now()%SECS_PER_DAY>=81000) { // 8:30am / 10:30pm
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Mode=Constant;
  ReefAngel.DCPump.Speed=30;
} else if (InternalMemory.DCPumpMode_read()==11) { 
  // Custom Mode and nothing else going on
  ReefAngel.DCPump.UseMemory=false;
  ReefAngel.DCPump.Mode=modes[rmode];  // Put the mode to the random mode :)
  ReefAngel.DCPump.Speed=InternalMemory.DCPumpSpeed_read(); // Set speed from portal
} else {
  ReefAngel.DCPump.UseMemory=true; // Will reset all values from memory
}

////// Place your custom code above here

// This should always be the last line
ReefAngel.Portal( "paulturner911" );
ReefAngel.ShowInterface();
}

void DrawCustomMain()
{
int x,y;
char text[10];
// Dimming Expansion
x = 15;
y = 2;
for ( int a=0;a<6;a++ )
{
if ( a>2 ) x = 75;
if ( a==3 ) y = 2;
ReefAngel.LCD.DrawText( COLOR_DARKGOLDENROD,DefaultBGColor,x,y,"Ch :" );
ReefAngel.LCD.DrawText( COLOR_DARKGOLDENROD,DefaultBGColor,x+12,y,a );
ReefAngel.LCD.DrawText( COLOR_DARKGOLDENROD,DefaultBGColor,x+24,y,ReefAngel.PWM.GetChannelValue(a) );
y += 10;
}
pingSerial();

// Parameters
#if defined DisplayLEDPWM && ! defined RemoveAllLights
ReefAngel.LCD.DrawMonitor( 15, 43, ReefAngel.Params,
ReefAngel.PWM.GetDaylightValue(), ReefAngel.PWM.GetActinicValue() );
#else // defined DisplayLEDPWM && ! defined RemoveAllLights
ReefAngel.LCD.DrawMonitor( 15, 43, ReefAngel.Params );
#endif // defined DisplayLEDPWM && ! defined RemoveAllLights
pingSerial();

// Main Relay Box
byte TempRelay = ReefAngel.Relay.RelayData;
TempRelay &= ReefAngel.Relay.RelayMaskOff;
TempRelay |= ReefAngel.Relay.RelayMaskOn;
ReefAngel.LCD.DrawOutletBox( 12, 84, TempRelay );
pingSerial();

// Date and Time
ReefAngel.LCD.DrawDate( 6, 122 );
pingSerial();
}

void DrawCustomGraph()
{
}

Re: PaulTurner911 Code

Posted: Fri Sep 13, 2013 5:32 am
by lnevo
Ok not sure where the missing line went between NTM and night mode it was gone for the past few pages. Please try the above code.
All times are UTC-07:00
Page 3 of 9

Powered by phpBB® Forum Software © phpBB Limited