Reef Angel Forum

I have been trying for over a week on this with no luck. I have two Win7 machines that I have been trying to setup the wifi attachment with. I am unable to communicate with the usb cable over the wifi utility and get a error serial message and I tried using putty but never got a connection.
What are my other options?

Can you post the message you are getting on both wifi utility and putty?

I had much better luck today working off another machine. I now have a blinking green light and the client says trying to connect to your router...

Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 2 88548 3 wifly-GSX-441-r1057
< 5 74684 3 web_app-GSX-112
< 8 46812 3 wps_app-GSX-131
< 10 66749 3 eap_app-GSX-105
< 12 51053 0 web_config.html
< 25 512 0 link.html
< 26 7268 0 logo.png
< 28 1052 10 config
< 29 1052 10 user
<
< 164 Free, Boot=2, Backup=2
< <4.41>
> load user
< load user
< AOK
< <4.41>
> save
< save
< Storing in config
< <4.41>
> save
< save
< Storing in config
< <4.41>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.41>
> set w l 5
< set w l 5
< AOK
< <4.41>
> set w s Geaux
< set w s Geaux
< AOK
< <4.41>
> set w p www.aaaa
< set w p www.aaaa
< AOK
< <4.41>
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.41>
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.41>
> save
< save
< Storing in config
< <4.41>
> reboot
< reboot
> $$$
< CMD
> show n
< show n
< SSid=Geaux
< Chan=1
< Assoc=OK
< Rate=12, 24Mb
< Auth=OK
< Mode=MIXED
< DHCP=OK,renew=453596
< Boot=2240
< Time=FAIL
< Links=1
< <4.41>
> get i
< get i
< IF=UP
< DHCP=ON
< IP=10.0.0.58:2000
< NM=255.255.255.0
< GW=10.0.0.1
< HOST=198.171.134.6:80
< PROTO=TCP,
< MTU=1524
< FLAGS=0x6
< TCPMODE=0x0
< BACKUP=0.0.0.0
< <4.41>
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Your Reef Angel Wifi Attachment is now configured with the settings provided.
---------------------------------------------------------------------

If the blue LED is still blinking, it means that the Reef Angel Wifi Attachment could not connect to your wifi network.

That looks like it is up and running now.
The ip address reported is 10.0.0.58.
You should be good to go.

Thank you for the help Rob.
I have everything setup and got my DNS setup and I can connect to my device while on my network but I cannot connect from an external network. I can see that port 2000 is open but I did not configure the dns update information into my router and maybe that is the issue. I will try to get it connected more this weekend.

What router changes are necessary for this traffic?

You need to setup port forwarding on your router.