hooked up new unit. only get green power and red flashing status and nothing on the screen. help.
thx
flashing red status
-
rossbryant1956
- Posts: 471
- Joined: Sat Jan 14, 2012 2:08 pm
- Location: Montgomery Village, MD
flashing red status
Roscoe's Reefs - Starting Over Again:
Building new 29g Nano after landlord went berserk over my 4 75 gallon tanks, Multiple RA's, Water mixing stations, etc. Your help welcomed in remembering all I've forgotten.
Building new 29g Nano after landlord went berserk over my 4 75 gallon tanks, Multiple RA's, Water mixing stations, etc. Your help welcomed in remembering all I've forgotten.
-
rossbryant1956
- Posts: 471
- Joined: Sat Jan 14, 2012 2:08 pm
- Location: Montgomery Village, MD
Re: flashing red status
Not quite sure how to do that. Looking at manuals now. This will get easier, I'm sure.
Roscoe's Reefs - Starting Over Again:
Building new 29g Nano after landlord went berserk over my 4 75 gallon tanks, Multiple RA's, Water mixing stations, etc. Your help welcomed in remembering all I've forgotten.
Building new 29g Nano after landlord went berserk over my 4 75 gallon tanks, Multiple RA's, Water mixing stations, etc. Your help welcomed in remembering all I've forgotten.
Re: flashing red status
http://www.reefangel.com/files/ReefAngelInstaller.exe
Download and install.
Then start Arduino and open ReefAngelSimple
Then, click upload
Download and install.
Then start Arduino and open ReefAngelSimple
Then, click upload
Roberto.
-
rossbryant1956
- Posts: 471
- Joined: Sat Jan 14, 2012 2:08 pm
- Location: Montgomery Village, MD
Re: flashing red status
Thx, trouble w internet here at home. Will do so in the morning and post results. Thx.
Roscoe's Reefs - Starting Over Again:
Building new 29g Nano after landlord went berserk over my 4 75 gallon tanks, Multiple RA's, Water mixing stations, etc. Your help welcomed in remembering all I've forgotten.
Building new 29g Nano after landlord went berserk over my 4 75 gallon tanks, Multiple RA's, Water mixing stations, etc. Your help welcomed in remembering all I've forgotten.
-
rossbryant1956
- Posts: 471
- Joined: Sat Jan 14, 2012 2:08 pm
- Location: Montgomery Village, MD
Re: flashing red status
Studied the manuals, reinstalled sw, followed instructions, opened arduino, can't find anything called reefangelsimple. Pls advise.
Roscoe's Reefs - Starting Over Again:
Building new 29g Nano after landlord went berserk over my 4 75 gallon tanks, Multiple RA's, Water mixing stations, etc. Your help welcomed in remembering all I've forgotten.
Building new 29g Nano after landlord went berserk over my 4 75 gallon tanks, Multiple RA's, Water mixing stations, etc. Your help welcomed in remembering all I've forgotten.
-
rossbryant1956
- Posts: 471
- Joined: Sat Jan 14, 2012 2:08 pm
- Location: Montgomery Village, MD
Re: flashing red status
Found it. Worked.
Is there a post somewhere that tells me what all I can do with this and what to do next? Thx all.
Is there a post somewhere that tells me what all I can do with this and what to do next? Thx all.
Roscoe's Reefs - Starting Over Again:
Building new 29g Nano after landlord went berserk over my 4 75 gallon tanks, Multiple RA's, Water mixing stations, etc. Your help welcomed in remembering all I've forgotten.
Building new 29g Nano after landlord went berserk over my 4 75 gallon tanks, Multiple RA's, Water mixing stations, etc. Your help welcomed in remembering all I've forgotten.