Reef Angel Forum

Hello,
Should the interface with the installer look like the tutorial? Mine looks the same as the old one with the same functions. I have recently removed all my earlier reefangel programs and updated to the latest stuff including the new libraries.

Thanks,
Rob

I have one powerhead plugged in. I have port 4 and 5 in "always on" right now because I am not using those outlets for wave making, only to run a powerhead all the time. It seems to have stopped cycling, and I have successfuly uploaded a couple more times. Thank you for you help.

I have not timmed it but every 10 minutes or so. The oulet is being turned off, thought maybe it was the light but it is fine and has never given me any problems.

I tried the suggestions that you made but it did not help. I uninstalled the "Reef Angle Controller" then downloaded and installed it again. I then updated the libraries again and was able to upload my good PDE file. Everything is working now, except it is cycling my main lights. Going to ...

The controller is now cycling my main lights on and off, it has never done that before.

I think it might be a Com port issue. When I go to RAgen and click "find controller" it says it can not find Com port 7. I went to the device manager and changed the port that is was showing from 4 to 7 but does not make a difference. I aslo removed the Com device and plugged the cable bac...

Hello all, Well I had the PDE running, WiFi working. Even had the Iphone app up, then I decided to try and get a signature banner up. I read the thread that covers how to modify the PDE, made some changes, ran verify in the Audrino program to check it, then uploaded it to the board. I then diconnect...

I have the app working and it is great, thank you for all your work. Is it possible to have the app display the same information but not be able to change anything, just monitor? I ask because my Daughter is a great help with the tank and would be great if I could put the app on her phone also but n...

So lets say in the internal memory file that I have genrated I have a set of light tuning on at 1400 and off at 2200. And a few days later I want to have the lights come on at 1300 and off at 2100, do I write code to make that change, or do I make another mem file and change it there and reload it a...

Hello all, I have read over and over again that once you upload a memory file that you do not have to do it again. I understand that the memory file is allowing certain options for the pde file to use. What I dont understand is if I want to change the lighting period for a set of lights, how do I do...

Okay,

Progress, I can see the Reef Angle Web Server now when I go to the address. Now I need to get the settings in the PDE right, tank is going wonky now. Thank you for your patience and help Roberto.

The following are the paths, so I need to change them to exactly what you have typed?

sketch: C:\Users\Rob\Documents\Arduino

Libraries: C:\Users\Rob\Documents\RAGen-v110-static\RAGen-v110-static

Arduino folder: C:\Users\Rob\Documents\RAGen-v110-static\RAGen-v110-static

I just loaded the following code from RAGen with the WiFi check box checked, still can not display anything from that address. Sorry the post is so long, do not know how to use the little boxes that you can scroll in. // Autogenerated file by RAGen (v1.1.0.127), (01/21/2012 17:20) // RA_012112_1720....

The following is a paste of the settings after using the utility. I believe the line that I have placed some (****) by is not right. I also took out some information that I did not think should be posted and replaced the information with (XXXX). After reading more threads it looks like my WiFi is no...

I have tried typing in the IP of the device into the brouser like the manual says to do and I get nothing. I believe I should see a portal type web page for the controller.

Hello All, I have completed the "how to set up my WiFi Attachement" walkthrough successfully. The green light is slowly blinking and seems fine. I can even see it when I go into my router although it does not have a name assosiated with it, it is showing the same IP address that was shown ...

Thank you that was it lol. Now looking to figure out what to do next. for the help.

Hello all, I am back to trying to get stuff sorted out. I am trying to use the WiFi utility and it shows an error "unhandeld exception" as soon as I start it. I am working with a new laptop and it has .NET 4 installed. Is the utility compatible with it? Certainly might not be the problem b...

When I try to run the graphical utility again it will only let me choose comm port 1. When I set up the controller it was on com port 3. Now when I do things following the directions in the utility nothing gets sent to the wifi adapter. It still sits there blinking the green light though.

I used the wifi graphical utility to set it up. I will run it again and see. I am just trying to get the controller steady for now. Would like to get the remote monitoring done since I am going out of town for a few days next week. Not going to start a dosing other than ATO till I am back and can be...

Thanks, do not see anything like that. It is connected to the controller and is doing the slow green blink. Maybe it is not on the network? I do not remember configuring it onto the network. Will keep working it. The other stuff is all working great, thank you for all the help Roberto.

Okay, I have the WiFi adapter configures with the computer as the tutorial stated. I have a domain with Dyndns. I have gotten into my router and set up the DDNS to reflect the domain. I think I need to find the WiFi adapter on the network now but I have several things on the network and I do not kno...

Chris, first thing you want to do is go to http://www.dyndns.org, create a new account and setup a new hostname. By doing this, you will create a new host address. Something like "chris.dyndns-remote.com". What this will do is bind the chosen host address (chris.dyndns-remote.com) to your...

Thank you roberto that might make a difference.

Well, trying to switch over all my stuff to the controller. Having some issues, the lights are not on the scedule correctly. When I first pluged them in I wanted to be sure I had the right outlets and such and turned the lights on via the control display. After both sets of light came on I could not...

Hello,

So is the DYN email server thing a paid service? I have registered with the site and do not have a problem paying a small fee for this APP to work, but wanted to check and see before buying a years subscription to the site.

Okay got it to all load this morning without errors. Not sure what I did different but it loaded this time.

Is it okay to have the PH probe and temp probe connected the the controller when I upload to it? My computer is fairly close and I am just plugging the cable to the controller while it is still hooked up to the sensors.

Yes I was able to upload the simple demo files.

When I try to upload to the board it looks like it is loading but when it finishes it says "Problem uploading to board. See (then the web site for trouble shooting).