Reef Angel Forum

No i only have a WL expansion, not an expansion hub. I'm fairly certain it didnt get wet during the leak as the side of the tank where it is positioned didn't wasn't overflowing (unfortunately my tank doesn't sit exactly level)

Hi Guys, So today i started getting a bunch of notifications from Reef Angel telling me my water level is low. The emails told me my water level was 0 as opposed to its normal level of 88-92. When i got home a few hours later i found the tank was overflowing as the ATO pump had been stuck in the on ...

Thanks ROberto, after some issues with my router I was able to set up Port Forwarding and now all is working fine. Now it's time to set up external access

I just used the wifi attachment to set up port forwarding and it said that was working fine. However that port checker is now showing port 2000 as closed. How do i add the new ip address to the wifi attachment? And i'm confused as to how the web portal can receive the current tank parameters like pH...

Hi Roberto,

Yes port forwarding is set up fine. How would i check if it's assigned a new ip address to the attachment?

I reset it again and that seems to have worked however it is still saying unreachable address so i'm still unable to change what is on through the portal. All i can do is see basic tank stats but i really need to be able to toggle the relay box.

Hi Guys, So i had my reef angel set up and running fine for a couple of months an then unexpectedly with no changes made to any settings the wifi attachment seems to have stopped sending data. There's no blue lights linking but whenever i check the portal it says last data was received on the 23rd o...

Hi Roberto, does that just go where the old ATO code was or should it go in the custom code section? Thanks for all your help!

Definitely not creating a siphon as the ato reservoir is below the tank and the hose output is about 8cm above water level so there's no way it could create a siphon and even if it did, that would result in water flowing down into the reservoir leaving a lower water level. My issue is that mater lev...

Cheers mate, These are the codes I'm using right now which rely on water level. First one is for ATO and second one is too ensure pump switches off if water level gets so high: ReefAngel.WaterLevelATO( Port6,60,88,92 ); ////// Place your custom code below here if (ReefAngel.WaterLevel.GetLevel() >= ...

Hi guys,

Just wondering if there's a way i can log the water level. I have the waterlevel expansion and i was just wanting to generate some simple graphs like the default ph and Temp ones but for waterlevel. Any ideas how to do this?

Haha bugger thanks for that, i generated that code with the wizard so I'm not sure what's going on there :\ Also any tips on how i can get the water level to appear on the homescreen of the console? I know there's a whole separate list of code but i was hoping i could just add the water level to the...

Hi guys, I'm using the water level expansion at the moment to run my ATO. I was wondering if there is some code i can put in that will instantly shut off the ATO port in case the water level gets too high. Say the reef angel gets rebooted and the pump automatically runs for a while, if it goes over ...

Just thought I'd leave a final update here incase anyone else has similar problems in the future. Thanks a lot to Roberto's help we managed to nail down that the wifi adapter couldn't achieve a solid connection to my wireless network as the router was too far away. After purchasing and setting up a ...

So i plugged in the wifi attachment to my pc and ran the Utility as it clearly wasn't working. I seem to be getting a lot of Unknown errors and being told to take the plug in and out. Then when it does work and i try and connect i get this: Opening Serial Port... Verifying speed at 9600 baud Connect...

Hi guys, I'm looking to set up ATO using my water level expansion but i'm a little clueless on how to code it all. Anyone have any ideas? Another quick question when you set the High and Low parameters in % what does each mean? Is low the level at which the pump will turn on and high when it will tu...

Hmm no I have a netgear dgn2200v3. I'm not entirely sure, now i can't see the port forwarding exemption in my router settings and when i try and test to see if the port is open i get told it is closed. But when i try adding in port forwarding on my router it says that the rule already exists :\

I've tried setting up port forwarding on my router but for some reason it's not working. I don't have a static IP address and can't get one, does this mean I can't port forward? I've never had this problem when i've needed to forward ports for games before. Also overnight when nothing has changed at...

Hi guys, I'm just trying to set up the wifi. I've been able to set it u seemingly okay with all the code and the attachment has the green light flashing. However i'm not sure how i connect to it using the app or the portal. When i try putting in my ip address in the internet with the /wifi after it ...