Reef Angel Forum

This is confusing I have two arduino with different content and they are in different folders. I am going to uninstall them and install again hopefully only one this time.

Where did the Wizard go? I downloaded RA and CS to new computer, everything seems to be working but I can't change my code because the Wizard is gone. Is this a new version of RA? Please advise.

In my case the pH dips go down usually to 6.03 sometime 5.98. The temp usually goes down to 0.
I had to lower the pH alert to 4.8 to stop receiving the alerts every couple hours.

No my probes are deep enough and the level is pretty stable. Anyway thanks for the suggestion.

pH plot.jpg On the website chart, usually on the pH plot every now and then (once or twice daily) a reverse peaks appear. My pH is pretty stable above 8 and these peaks goes down to 6 and immediately get back to above 8. See the attached picture from my website chart. Sometimes similar thing happen...

Thanks.

I am trying to decrease the max. % of lights (D and A) in my current sketch and when I try upload it it says sketch too big. 32,396 bytes of 32,256 max. I know that the RA has small memory but I am editing just one parameter in the existing sketch, so how can it be a problem. The only thing I can th...

OK, thanks. Now it works.

Roberto, I replaced the the LCD screen but it didnt help, the screen is still blank. Now even after unplugging and plugging in it doesn't display any info, just blank. Is there anything I should do to get it started?

After upgrading to Ardiuno 1.0.1, library 1.0.7 and client 3.0 eventually everything work like programed with the RA wizard. However the LCD display on the controller malfunctions. When I unplug the controller and then plug it in back the LCD displays all the info (temps, pH) the green LED is on sol...

Wherever on your computer.Then go Setting and Memory file and brows to where you saved the file.
Maybe it will work for you, it didn't for me.
Good luck.

After upgrading to new RA 1.0.7 and library 1.0.7 and Client 3.0 I cant refresh the memory it gives me the message:Unable to retrieve controller memory settings. I tried to download the RAMemory as suggested below, but it didn't help. Download the RAMemory.ini file attached to this post and save to ...

Thanks

OK, managed to upload it after choosing the RA w/optiboot. Is that OK?

I see, under the tools, board the RA+ is marked. If I change it to RA the message is sketch is too big.
Should I choose the RA w/ optiboot?

No just RA

Reinstalled the RA Installer 1.0.1 with new library 1.0.7 Went though Wizard and verified/compiled the sketch, but cant upload it. Below is the error: avrdude: Version 6.0, compiled on Apr 6 2012 at 19:29:19 Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ Copyright (c) 2007-2009 Joerg Wu...

I dont think it is LCD since when I unplug the power and plug it again it does work for a while but then freezes and if I push the joystick it flickers, cant see anything.

Do you have an email so I can send you a short mp4 showing the flickering?

Should I try to uninstall the controller and reinstall everything from scratch? I really dont know what else to do.

As I said I can't see anything (that is the problem).

It does not respond to the joystick at all.

Roberto, I still have problems with the controller. While I am waiting for Dave to help me with the client I uninstalled the client completely. Even without the client the controller keep freezing. It doesnt work, cant read the temp or pH. When press the button on the controller the small display ge...

Do I need to mark on the WiFi attachment in the wizard even though I don't have it? Is this necessary for the client or portal to work?

I know, I need to get Dave to help me with the client but the RA controller doesn't work either. It freezes completely, the pH probe doesn't work. I wanted to start from scratch so I uninstalled everything and installed again the newest version. Then used the wizard to generate the sketch and upload...

I have RA. It took me a few hours but eventually I managed to upload the new version of RA installer and even to upload new sketch without an error. The end results however is not very satisfying; the Client still get stuck, the pH probe went crazy from 11 to 2 and I cant refresh the memory it gives...

avrdude: Version 6.0, compiled on Apr 6 2012 at 19:29:19 Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ Copyright (c) 2007-2009 Joerg Wunsch System wide configuration file is "C:\Program Files (x86)\Reef Angel Controller\hardware/tools/avr/etc/avrdude.conf" Using Port : \\.\CO...

It says error uploading