Reef Angel Forum

Thanks for the tip, how would I remove it directly from the INO file?

I need to learn how to remove some of the graphics from the screen, im sure that would free up some space too. I will look at getting the upgrade

The reason i ask is i am contemplating doing a DIY LED build, and I recently purchased a 2nd MP40 so was thinking about getting the RF module for the Vortechs. I am wondering if that is going to be exceeding the memory limits of the current board. I also currently have wireless and the dual dosing p...

The new replacement board that is on the site with more memory, does it have more memory than the controller that I purchased back in December?

Once you do the library update do you need to regenerate the memory file?

Thanks, that took care of it, and it also solved a few other things that i was fighting

Ok I am getting the update now, odd, i stripped all of the code for the expansion out and it was still doing it.

I have real problems now, my ATO is staying on all of the time, I stripped out all of the expansion box items as it started to happen when my moon lights (box0_port1) were scheduled to come on. I repushed the code and it is still on, thankfully i was sitting there when it did it so i was able to pul...

So I have something thats amiss with my expansion relay. from the portal I am able to turn on n off my pumps, but with the new code they are not being turned on. here is my INO file // Autogenerated file by RAGen (v1.2.1.158), (02/20/2012 22:17) // RA_022012_2217.ino // // This version designed for ...

Great Thanks just did a few comparisons from the old to the new, just have to learn the code, I have found that Notepad++ is great for making it readable vs notepad

This compiles without any errors, is this the proper way?
ReefAngel.FeedingModePorts = Port1Bit | Port3Bit;
ReefAngel.FeedingModePortsE[0] = Port3Bit | Port4Bit;

I think I figured it out ReefAngel.FeedingModePorts = Port1Bit | Port3Bit; ReefAngel.FeedingModePortsE[0] = Port3Bit | Port4Bit; ReefAngel.WaterChangePorts = Port1Bit | Port3Bit | Port5Bit | Port7Bit | Port8Bit; ReefAngel.WaterChangePortsE[0] = Port3Bit | Port4Bit; ReefAngel.OverheatShutoffPorts = P...

What is the proper way to list the relay expansion ports in the lighting, feed mode etc?

Thanks that did it, I should know to unistall and start from scratch

I am getting this error My Documents\Arduino\libraries\DS1307RTC\DS1307RTC.cpp:94: error: 'class TwoWire' has no member named 'write'

Any ideas? Started from scratch with my config

Ok great

Ok, finally had some time to do the box swap, the problem follows the box. tried to swap the cable etc, same result,

The swapping of the cable had no impact, I will swap the boxes now and see what happens in the morning

Swapped the cable, should know tomorrow if it makes a difference or not.

I can do that, let it run for a few days and see if i start getting odd results

I dont have the screen programmed for the expansion, but the client does show both ports are on. If I pull the power cord out of the expansion, not the main relay box, when i plug it back in the relays will turn on

// Autogenerated file by RAGen (v1.1.0.126), (01/29/2012 19:29) // RA_012912_1929.pde // // This version designed for v0.8.5 Beta 17 or later /* The following features are enabled for this PDE File: #define DirectTempSensor #define wifi #define RelayExp #define SIMPLE_MENU #define ENABLE_ATO_LOGGIN...

port 13 and 16

I haven't forgot about this, just been slammed with work. It does appear that port 3 is working but port 6 still in order for it to come on I have to power cycle the relay box and then it comes on. I did check to make sure that none of the pins were bent and they were ok.

Yea, I will do that tomorrow night when I get home. I might have a few of them laying around here from old monitors if that is the problem

cool thanks, Place the boolean above wich setup? toward the top near where all of the .h files are listed?

I wish I knew how to do this suff....... but I am learning lol

Correct that port should be on at all times. It seems that it does shut off on its own, i am having the same problem with port 6 too, if i power cycle the entire relay box it seems to bring them back on

Thanks that did it i reversed all of the expansion module relay ports that I had manually done and now when I do feeding mode the proper channels turn off. one issue i have is ports 3 and 6 on the relay expansion do not turn on properly unless i power cycle the relay expansion, they show on in the c...

I was thinking about this tonight, is there a way to set the dosing pumps NOT to run if the PH is at 8.20 and if it should drop below 8.0 to have them start running again?

Actually it makes sense, I will update my PDE when i get home tonight

thanks