Reef Angel Forum

Reef Angel plus controller ...........................$450.00 Free Shipping in US International at buyers expense 2 temp probes Bluetooth wifi 2 8 outlet control boxes dual dosing pump expansion hubs RF Expansion for Vortec Control pc programming cable. Not needed after up and running can do via Blu...

I have this on both of my RA's now, works great!

take your time. i appreciate it

I just played around with the code and if I put "StandLight" on port 9 it reboot loops
if I put StndLight its fine

thoughts?

ReefAngel.CustomLabels[9]="StndLight";

was there ever a solution to this? I just ran into it myself, thought it was only the 2nd page of labels. I have yet to try one at a time to see which line is the offender.

I totally get it. I was almost completely out of the hobby because of my last job. Now with my new one, i am setting up a second tank for my home office. Stress is a bad bad thing

Thanks Binder, Didnt know if it was a future request or not.

I have them setup with internal and external individual dns. i use Home with one port and DNS entry, Away with another port and DNS entry. I can read temp and ph, but the labels dont line up unless i change forum login names and resync. not a huge deal but it can be a bit cumbersome

Is there a way to monitor 2 controllers from one phone\app?
I have 2 tanks each with their own RA, one has a single relay, the other has 2.
would be nice to swap between them.

Currently I am using the home and away, different ports, but the labels dont line up.

Thanks!

was thinking that too, then can run them independent of each other. So that raises another question, can the vortechs be on both the RA and on the reeflink?

set one up on the RA and one up on the reeflink?

I am going to be hanging 2 Radions over my tank and I am wondering i can control them independent of each other. It is a square tan so i will have one in the front and one in back.

I am wanting to turn the front one up higher than the rear..

Thanks

Has anyone connected the RA to Samsungs Smartthings? I was thinking about the ATO, instead of having cords running with the fill line, have just the fill line. Its smaller and think i can route it through the floor, but not sure i can do the extension cord that powers the pump route as well. My tank...

How many feet of lift will it do?

That looks great keep up the good work

Sent from my Galaxy Nexus using Tapatalk 2

Tried that too, with no change in speed. I normally run reef crest and prior to the lib change it worked flawlessly

I have set it to 100 as well, also tried to set it lower around 50 and it didnt seem to impact the pump speed at all

I am having a similar issue, my pumps are getting the "mode" from the App as well as the Portal, but the speed on them is not increasing at all. I changed the speed setting in the App to be 255 with no change, if I set the mode to 10 or 5 i do get an increase in speed. In the app I have re...

Thanks for your help, I am back to 100% now.
I need to setup my original INO side-by-side with the new one next time.
also added this in //ReefAngel.RF.SetMode(); and the vortech now shows up on the portal

Ah no shoot I am my own worst enemy I am using 1 switch

Sent from my Galaxy Nexus using Tapatalk 2

I think we delt with that the last update lol, so much for learning from my mistakes

what about the ATO Issue, I have it setup in the code as a standardATO, I checked the switch and it is good, goes open when all the way up and closes when down.

No problem, but it doesnt look like it is recognizing it The following features were automatically added: Watchdog Timer Version Menu The following features were detected: Dimming Signal Wifi Attachment Custom Main Screen Relay Expansion Module Dimming Expansion Module Number of Relay Expansion Modu...

So the PWM is working ok now. my ATO is still not working properly and here is the copy of the complile avrdude: Recv: p [70] avrdude: Recv: r [72] avrdude: Recv: o [6f] avrdude: Recv: j [6a] avrdude: Recv: e [65] avrdude: Recv: c [63] avrdude: Recv: t [74] avrdude: Recv: x [78] avrdude: Recv: . [00...

Added that line and same result with the Vortech on both the Portal as well as the App
for now it seems my ATO is working properly.
The PWM I will have to recheck tomorrow as it is past the time for the lights to be active.

Yes I removed the line of code.
Ill add the other line and report back

Thanks for your help as always

Add this to the INO file?
on the screen it is also showing nothing % wise.
yes in the app I verified that it was unchecked

Ok now I have another issue. (if you want I can start a new thread on it) My ATO keeps running and it does timeout but if when I clear the timeout it starts filling again. On the portal I do not see the vortech setting, my PWM module is not changing %. In the Droid app, the vortech is showing the wr...

OK will do

Silly question if I loaded it all into memory can I change the PWM slope via the portal and not have to worry about pushing the code?

Sent from my SAMSUNG-SGH-I717 using Tapatalk 2

Here you are, I commented those lines out so I could get the controller back online #include <ReefAngel_Features.h> #include <Globals.h> #include <RA_Wifi.h> #include <Wire.h> #include <OneWire.h> #include <Time.h> #include <DS1307RTC.h> #include <InternalEEPROM.h> #include <RA_NokiaLCD.h> #include ...

These are the exact errors I get sketch_aug04b:82: error: 'class RA_PWMClass' has no member named 'Channel0PWMSlope' sketch_aug04b:83: error: 'class RA_PWMClass' has no member named 'Channel1PWMSlope' sketch_aug04b:84: error: 'class RA_PWMClass' has no member named 'Channel2PWMSlope' sketch_aug04b:8...