Uapp Graph shows no Data to display always.

Community contributed apps
binder
Posts: 2871
Joined: Fri Mar 18, 2011 6:20 pm
Location: Illinois
Contact:

Re: Uapp Graph shows no Data to display always.

Post by binder »

SouthernReefer wrote:
rimai wrote:I am very confused.....
Let me ship you another board and we go from there.
PM me your shipping address.

Seems good this morning. I went to wake up the screen barely touched it, was unresponsive again.. nd rebooted twice... I'm loosing a bit of faith.....
I had my star be randomly unresponsive like that and it was an issue with libraries. Roberto fixed it and it's been great since. If you are using arduino and local libraries, make sure you are using the latest dev branch libraries from github. I'm assuming that you have (and I haven't looked back through this thread). The release on 12/2/19 fixed my problem, git commit hash is 3c145e7. So just double check your library version.... it can't hurt.

To double check, just close arduino. Move your current libraries folder to libraries-old. Download the latest dev branch and unzip to the libraries folder. Then launch arduino and upload your code.

If you have already done this, then ignore my comment. :-)

Sent from my Pixel 2 using Tapatalk
SouthernReefer
Posts: 158
Joined: Thu Nov 14, 2019 2:51 pm

Re: Uapp Graph shows no Data to display always.

Post by SouthernReefer »

binder wrote:
SouthernReefer wrote:
rimai wrote:I am very confused.....
Let me ship you another board and we go from there.
PM me your shipping address.

Seems good this morning. I went to wake up the screen barely touched it, was unresponsive again.. nd rebooted twice... I'm loosing a bit of faith.....
I had my star be randomly unresponsive like that and it was an issue with libraries. Roberto fixed it and it's been great since. If you are using arduino and local libraries, make sure you are using the latest dev branch libraries from github. I'm assuming that you have (and I haven't looked back through this thread). The release on 12/2/19 fixed my problem, git commit hash is 3c145e7. So just double check your library version.... it can't hurt.

To double check, just close arduino. Move your current libraries folder to libraries-old. Download the latest dev branch and unzip to the libraries folder. Then launch arduino and upload your code.

If you have already done this, then ignore my comment. :-)

Sent from my Pixel 2 using Tapatalk
I used the web wizard.
SouthernReefer
Posts: 158
Joined: Thu Nov 14, 2019 2:51 pm

Re: Uapp Graph shows no Data to display always.

Post by SouthernReefer »

What's more concerning is the random reboots thankfully I was home.
SouthernReefer
Posts: 158
Joined: Thu Nov 14, 2019 2:51 pm

Re: Uapp Graph shows no Data to display always.

Post by SouthernReefer »

Random reboots continue to happen. I've unplugged everything not essential so it doesn't get triggered. I'm no where near it not doing anything or touching it. It just reboots. Same cost that's been on it from day 1 yet this is very new behavior after we troubleshot...
SouthernReefer
Posts: 158
Joined: Thu Nov 14, 2019 2:51 pm

Re: Uapp Graph shows no Data to display always.

Post by SouthernReefer »

rimai wrote:I am very confused.....
Let me ship you another board and we go from there.
PM me your shipping address.
Are you are seeing my data now??? I did a test after I got fustrated from constant rebooting and lack of stability this morning and started unplugging things. I realized I still had a 0 to 10 cable plugged in, but not plugged in to anything. I have 0 code referencing that, but it's graphing now. Can you see anything on your side? In waiting to see if I reboot again before I can feel good about plugging anything other than my return pump into this.
rimai
Posts: 12881
Joined: Fri Mar 18, 2011 6:47 pm

Re: Uapp Graph shows no Data to display always.

Post by rimai »

What is a 0 to 10 cable?
I see some data from this morning.
Roberto.
SouthernReefer
Posts: 158
Joined: Thu Nov 14, 2019 2:51 pm

Re: Uapp Graph shows no Data to display always.

Post by SouthernReefer »

rimai wrote:What is a 0 to 10 cable?
I see some data from this morning.

VDM.... The port on the co troller to allow 0 to 10 controll of pumps and or lights. It's the network looking jack on the bottom of the controller...
SouthernReefer
Posts: 158
Joined: Thu Nov 14, 2019 2:51 pm

Re: Uapp Graph shows no Data to display always.

Post by SouthernReefer »

rimai wrote:What is a 0 to 10 cable?
I see some data from this morning.

If it's talking it's not the head then that's bad. I'm still waiting to see if it randomly locks up and starts a reboot loop again however. I have a test devised for that.
SouthernReefer
Posts: 158
Joined: Thu Nov 14, 2019 2:51 pm

Re: Uapp Graph shows no Data to display always.

Post by SouthernReefer »

rimai wrote:What is a 0 to 10 cable?
I see some data from this morning.
Portal in the website now updates but still says unreachable address, although that may be normal??
rimai
Posts: 12881
Joined: Fri Mar 18, 2011 6:47 pm

Re: Uapp Graph shows no Data to display always.

Post by rimai »

Yes. Portal was created way before the cloud server.
We had to open port forwarding on the router to allow the portal to connect to it.
Then, Uapp was developed to take advantage of the cloud server connection.
If you want the portal to be able to connect, you will need to open port forwarding on your router.
Roberto.
SouthernReefer
Posts: 158
Joined: Thu Nov 14, 2019 2:51 pm

Re: Uapp Graph shows no Data to display always.

Post by SouthernReefer »

rimai wrote:Yes. Portal was created way before the cloud server.
We had to open port forwarding on the router to allow the portal to connect to it.
Then, Uapp was developed to take advantage of the cloud server connection.
If you want the portal to be able to connect, you will need to open port forwarding on your router.

Will alerts I write in there work without the port forwarding? The way I researched it before I bought this I didn't need to open ports forwarding, however alerts are much needed, and a big reason I bought a Controller. I rather not punch a hole in my network if I can avoid it....
SouthernReefer
Posts: 158
Joined: Thu Nov 14, 2019 2:51 pm

Re: Uapp Graph shows no Data to display always.

Post by SouthernReefer »

rimai wrote:I am very confused.....
Let me ship you another board and we go from there.
PM me your shipping address.
Are you still seeing data? I can't graph past 1040 am cst. I thought we had this fixed :(
SouthernReefer
Posts: 158
Joined: Thu Nov 14, 2019 2:51 pm

Re: Uapp Graph shows no Data to display always.

Post by SouthernReefer »

rimai wrote:Yes. Portal was created way before the cloud server.
We had to open port forwarding on the router to allow the portal to connect to it.
Then, Uapp was developed to take advantage of the cloud server connection.
If you want the portal to be able to connect, you will need to open port forwarding on your router.
3 more unexpected reboots this morning. I walked over as I heard a click, and it was a relay triggering. Wasn't ATO.. watched it reboot 3 times before I was able to interact with it again.... Thankfully I was home
Post Reply