I recently acquired a reef angel plus (second hand)
I am however experiencing difficulty in setting up the controller.
What have I done so far.
- Used the web wizard to generate a rather basic code (please see code below)
- Installed and connected the wifi attachment to our home network. (received the following message)#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <DCPump.h>
#include <PAR.h>
#include <ReefAngel.h>
////// Place global variable code below here
////// Place global variable code above here
void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
ReefAngel.SetTemperatureUnit( Celsius ); // set to Celsius Temperature
ReefAngel.Use2014Screen(); // Let's use 2014 Screen
ReefAngel.AddSalinityExpansion(); // Salinity Expansion Module
ReefAngel.AddPHExpansion(); // pH Expansion Module
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = 0;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = 0;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = 0;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = Port2Bit | Port4Bit;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;
// Ports that are always on
////// Place additional initialization code below here
////// Place additional initialization code above here
}
void loop()
{
ReefAngel.DayLights( Port1 );
ReefAngel.StandardHeater( Port2 );
ReefAngel.Relay.DelayedOn( Port3 );
ReefAngel.StandardHeater( Port4 );
////// Place your custom code below here
////// Place your custom code above here
// This should always be the last line
ReefAngel.Portal( "Henkie" );
ReefAngel.DDNS( "10.0.0.10:2000" ); // Your DDNS is Henkie-10.0.0.10:2000 .myreefangel .com
ReefAngel.ShowInterface();
}
- Wifi connection status.PNG (23.31 KiB) Viewed 9847 times
I did the test by inserting the IP address into my browser and was able to successfully turn the relays on and off.
However I cannot see my data on the portal nor on the app.
What have I done to combat the problem?
I entered by home networks IP address and added the IP address of the Reef Angel (ie 10.0.0.10) to be accepted via port 2000 (please refer to image below)
- Port Forwarding.PNG (9.91 KiB) Viewed 9847 times
Every time I upload the code it runs through the process, reboots the controller but indicated "Error uploading" (please refer to image)
- Error uploading.PNG (6.85 KiB) Viewed 9847 times
The portal still does not identify my controller neither does the app.
Any assistance will be greatly appreciated