DrewPalmer04 wrote:Please post your full code
Below is the full code:
#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <ReefAngel.h>
////// Place global variable code below here
unsigned long lastLowSal=now();
////// Place global variable code above here
void setup()
{
// This must be the first line
ReefAngel.Init(); //Initialize controller
ReefAngel.SetTemperatureUnit( Celsius ); // set to Celsius Temperature
// Ports toggled in Feeding Mode
ReefAngel.FeedingModePorts = 0;
ReefAngel.FeedingModePortsE[0] = 0;
// Ports toggled in Water Change Mode
ReefAngel.WaterChangePorts = 0;
ReefAngel.WaterChangePortsE[0] = 0;
// Ports toggled when Lights On / Off menu entry selected
ReefAngel.LightsOnPorts = 0;
ReefAngel.LightsOnPortsE[0] = 0;
// Ports turned off when Overheat temperature exceeded
ReefAngel.OverheatShutoffPorts = Port6Bit;
ReefAngel.OverheatShutoffPortsE[0] = 0;
// Use T1 probe as temperature and overheat functions
ReefAngel.TempProbe = T1_PROBE;
ReefAngel.OverheatProbe = T1_PROBE;
// Set the Overheat temperature setting
InternalMemory.OverheatTemp_write( 255 );
// Ports that are always on
ReefAngel.Relay.On( Port4 );
ReefAngel.Relay.On( Port5 );
ReefAngel.Relay.On( Port8 );
ReefAngel.Relay.On( Box1_Port1 );
ReefAngel.Relay.On( Box1_Port4 );
ReefAngel.Relay.On( Box1_Port6 );
ReefAngel.Relay.On( Box1_Port7 );
////// Place additional initialization code below here
////// Place additional initialization code above here
}
void loop()
{
ReefAngel.MHLights( Port3,0,40,23,30,5 );
ReefAngel.StandardHeater( Port6,249,251 );
ReefAngel.StandardFan( Port7,250,252 );
ReefAngel.StandardLights( Box1_Port5,23,30,23,32 );
////// Place your custom code below here
///// If salinity > 35.1 activate ATO pump until salinity < 35.1
if (ReefAngel.Params.Salinity<351) lastLowSal=now();
ReefAngel.Relay.Set(Port1,(now()-lastLowSal>120));
///// if skimmer cup full, turn off skimmer
if (ReefAngel.HighATO.IsActive()) {
bitClear(ReefAngel.Relay.RelayMaskOff,2);
}
else {
bitSet(ReefAngel.Relay.RelayMaskOff,2);
}
////// Place your custom code above here
