Reef Angel Forum

How about a cromebook?

So my RA+ has been sitting in a box for around for around 3 or 4 years. I am now in the process of put a planted tank up and want to use it again. Problem i am having is in that time we have transitioned to all ipads and do not have any computers left at home. Is there anyway to be able to reprogram...

After reading of the Tera term help form I got it. Thanks

after accidently doing a firm wear update on my wifi module it will no longer connect I get ** ERROR - Please disconnect and then reconnect the Reef Angel Wifi Attachment from the USB-TTL cable and try again. I have tried using terra term with the following script x=0 while x<>121 messagebox 'Start ...

I am having the same problem have down loaded everything wanting to make sure that I change the ssid to my one at home and the pass to my password at home for the wifi

Ok that was way more complicated than I understand. So I guess I will get lights that control there selfs

will an ra+ control reefbreeders

thanks worked great I just did not want to brake something

ok my little 2year old undid the retention ring around the breaker/fuse on the relay box and then pushed it in. I took the screws out of the top to try and open it to push the breaker/fuse out so I can put the retention ring back on but the lid does not open easily. any help would appreciated

#include <ReefAngel_Features.h> #include <Globals.h> #include <RA_Wifi.h> #include <Wire.h> #include <OneWire.h> #include <Time.h> #include <DS1307RTC.h> #include <InternalEEPROM.h> #include <RA_NokiaLCD.h> #include <RA_ATO.h> #include <RA_Joystick.h> #include <LED.h> #include <RA_TempSensor.h> #inc...

OK so port 6 is my ato pump controlled by a single low float switch. what i am wanting is for the ATO not to be able to be activated for 30min after my calk stir goes off to give the slurry time to settle. I am not sure that the code above will achieve that, but from what you just taught me will the...

OK i know that you are very busy but could you pleas explain to me what the numbers in there potions mean. i would like to learn why vs just having it given to me so i do not have to bother you next time

every 240min for 15sec. i have it set up as a dosing pump via the RA wizard

how do i set to have port 6 be able to come on only after 30min if port 7 has run. port 7 is a power head stirring kalckwash and port 6 is the ato pump using that water

a place that i found very helpful was portforward.com. i was able to look up my specific router and it gave me step by step instructions on how to set up port forwarding

i borrowed my neighbors probe, calibrated it, i placed it on the head unit and it appears to be working. this leads me to believe that the prob has already gone bad.

there are bubbles in the probe on up where the probe is blue, but none that i can see in the tip. the prob is only a few weeks old

it is stuck on 2.98, i placed it in a cup of watter and it stayed. even when i place it in calibration fluid it stayed at 2.98. i tried to recalibrate it and in the screen it only showers 0

it is stuck on 2.98, i placed it in a cup of watter and it stayed. even when i place it in calibration fluid it stayed at 2.98. i tried to recalibrate it and in the screen it only showers 0

My Ph probe will work fine for several hr and then goes to a Ph of 1, after a while it will slowly come back up to the 6 area, if i recalibrate it it will work for a few hr and then drop back to 1. any ideas

i have a 2wire router, and i have been unable to get the wifi upgrade the firmware. it tells me every time in the middle of upgrade that connection failed pleas disconnect and reconnect the wifi module

so i went and assigned the wifi a permanent ip address and it appears to be working again

i get ping ping timed out

the ip address for the wifi is 192.168.1.64, this is the one that i have the phone ap set to. the public ip address is 99.13.22.96 this is the one that i have the portal set to.

so i had the router forget the wifi and did the set up again, it worked for a few min and went back to unable to connect and the phone app stopped connecting again?

the router showes it connected in the list of devices.

my wifi had been working great with the ability to control from a computer. today it stopped working the portal gives me "unreachable address" the light still blinks green and the cell phone app will not work. i put it back on the computer and tried to reset it with no luck. i tried to go ...

all of the code has been from the wizard, i can now up load any code and they work for now, but they worked fine for 24hr, before they quit

i have run the test code and plugged in a power head to the port 7 and 8 as i toggle though it turns on, so why would the 2 stop working with other equipment on the preloaded code?

i am at work today, i will do that tomarrow, and now port 7 does not work