Screen stays backlit but is only black

[Mhumbach]

Hello, I am new here and have been loving my reef angel. Recently the screen blacks out but stays backlit, I can still control it from my phone and when I reboot the controller the screen turns back on. This is my code I believe.

#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <DCPump.h>
#include <ReefAngel.h>

////// Place global variable code below here


////// Place global variable code above here


void setup()
{
    // This must be the first line
    ReefAngel.Init(); //Initialize controller
    // Ports toggled in Feeding Mode
    ReefAngel.FeedingModePorts = Port1Bit | Port2Bit | Port3Bit | Port7Bit | Port8Bit;
    // Ports toggled in Water Change Mode
    ReefAngel.WaterChangePorts = Port1Bit | Port2Bit | Port3Bit | Port7Bit | Port8Bit;
    // Ports toggled when Lights On / Off menu entry selected
    ReefAngel.LightsOnPorts = 0;
    // Ports turned off when Overheat temperature exceeded
    ReefAngel.OverheatShutoffPorts = 0;
    // Use T1 probe as temperature and overheat functions
    ReefAngel.TempProbe = T1_PROBE;
    ReefAngel.OverheatProbe = T1_PROBE;
    // Set the Overheat temperature setting
    InternalMemory.OverheatTemp_write( 820 );


    // Ports that are always on
    ReefAngel.Relay.On( Port2 );
    ReefAngel.Relay.On( Port3 );
    ReefAngel.Relay.On( Port4 );
    ReefAngel.Relay.On( Port5 );

    ////// Place additional initialization code below here
    

    ////// Place additional initialization code above here
}

void loop()
{
    ReefAngel.Relay.DelayedOn( Port1,1 );
    ReefAngel.StandardHeater( Port6,778,781 );
    ReefAngel.Relay.DelayedOn( Port7,1 );
 
    ////// Place your custom code below here
    ReefAngel.SingleATO(true,Port8,300,0);
    if (ReefAngel.HighATO.IsActive()) ReefAngel.Relay.Off(Port8);


    ////// Place your custom code above here

    // This should always be the last line
    ReefAngel.Portal( "Mhumbach" );
    ReefAngel.ShowInterface();
}

[rimai]

What happens when you move the joystick?

[Mhumbach]

It stays black but the back light turns on. Im close to using up all of my memory the controller could that be triggering it?

[rimai]

Humm. Looks like you got a bad screen then.
PM me for RMA.