Wifi with 0.0.0.0 IP

Expansion modules and attachments
Post Reply
symon_say
Posts: 118
Joined: Sun Oct 09, 2011 6:04 am
Location: Dominican Republic
Contact:
Contact symon_say

Wifi with 0.0.0.0 IP

Post by symon_say »

I'm trying to configure my wifi attachment but everytime I set it on the wifi utility i get Ip 0.0.0.0:2000

Code: Select all

---------------------------------------------------------------------
Wifi Attachment Connected to COM9
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM9
> $$$
< CMD
< DHCP in 6718ms, lease=259200s
< IF=UP
< DHCP=ON
< IP=10.0.0.80:2000
< NM=255.255.255.0
< GW=10.0.0.1
< Listen on 2000
> factory RESET
< factory RESET
< Set Factory Defaults
> reboot
< <4.41> 
< reboot
Removing connection to COM9
---------------------------------------------------------------------
Factory Settings Restored
---------------------------------------------------------------------

Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM9
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM9
Connected to serial port COM9
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM9
---------------------------------------------------------------------
Wifi Attachment Connected to COM9
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM9
> $$$
< CMD
> ls
< ls
< 
< FL#    SIZ   FLAGS
<   2  79680   3 WiFly_GSX-2.36  
<  22   1052  10 config  
<  23   1052  10 user  
<  24  88548   3 wifly-GSX-441-r1057  
<  34  83648   3 WiFly_GSX-2.45  
<  78  86328   3 wifly-GSX-400  
<  79  46632   3 wps_app-GSX-131  
<  80  66240   3 eap_app-GSX-101  
<  81  74920   3 web_app-GSX-106  
<  82  37282   0 web_config.html  
<  83    512   0 link.html  
<  84   7268   0 logo.png  
< 
< 104 Free, Boot=24, Backup=78
< <4.41> 
> load user
< load user
< AOK
< <4.41> 
> save
< save
< Storing in config
< <4.41> 
> save
< save
< Storing in config
< <4.41> 
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.41> 
> set w l 5
< set w l 5
< AOK
< <4.41> 
> set w s ReefAngel
< set w s ReefAngel
< AOK
< <4.41> 
> set w p bluetang
< set w p bluetang
< AOK
< <4.41> 
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.41> 
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.41> 
> save
< save
< Storing in config
< <4.41> 
> reboot
< reboot
> $$$
< CMD
< Disconn from ReefAngel,INACTIVITY
< Auto-Assoc ReefAngel chan=3 mode=MIXED SCAN OK
< Joining ReefAngel now..
< Disconn from ReefAngel,INACTIVITY
< Auto-Assoc ReefAngel chan=3 mode=MIXED SCAN OK
< Joining ReefAngel now..
< Disconn from ReefAngel,INACTIVITY
< Auto-Assoc ReefAngel chan=3 mode=MIXED SCAN OK
< Joining ReefAngel now..
< Disconn from ReefAngel,INACTIVITY
< Disconn from ReefAngel,1:9
< Disconn from ReefAngel,1:9
< Disconn from ReefAngel,AUTH-ERR
> show n
< show n
< SSid=ReefAngel
< Chan=3
< Assoc=FAIL
< Rate=0, 1 Mb
< Auth=FAIL
< Mode=MIXED
< DHCP=FAIL
< Boot=0
< Time=OK
< Links=1
< <4.41> 
> get i
< get i
< IF=DOWN
< DHCP=ON
< IP=0.0.0.0:2000
< NM=0.0.0.0
< GW=0.0.0.0
< HOST=104.36.18.155:80
< PROTO=TCP,
< MTU=1524
< FLAGS=0x6
< TCPMODE=0x0
< BACKUP=0.0.0.0
< <4.41> 
> reboot
< reboot
Removing connection to COM9
---------------------------------------------------------------------
Your Reef Angel Wifi Attachment is now configured with the settings provided.
---------------------------------------------------------------------

If the blue LED is still blinking, it means that the Reef Angel Wifi Attachment could not connect to your wifi network.

Found router P9

Unable to setup port forwarding. This step will have to be done manually. For more information for your specific type of router, please visit http://www.portforward.com
Opening Serial Port...
Connected to serial port COM9
> $$$
< CMD
> ls
< ls
< 
< FL#    SIZ   FLAGS
<   2  79680   3 WiFly_GSX-2.36  
<  22   1052  10 config  
<  23   1052  10 user  
<  24  88548   3 wifly-GSX-441-r1057  
<  34  83648   3 WiFly_GSX-2.45  
<  78  86328   3 wifly-GSX-400  
> load user
<  79  46632   3 wps_app-GSX-131  
<  80  66240   3 eap_app-GSX-101  
<  81  74920   3 web_app-GSX-106  
<  82  37282   0 web_config.html  
<  83    512   0 link.html  
<  84   7268   0 logo.png  
< 
< 104 Free, Boot=24, Backup=78
< <4.41> 
< load user
< AOK
< <4.41> 
> save
< save
< Storing in config
< <4.41> 
> save
< save
< Storing in config
< <4.41> 
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <4.41> 
> set w l 5
< set w l 5
< AOK
< <4.41> 
> set w s ReefAngel
< set w s ReefAngel
< AOK
< <4.41> 
> set w p bluetang
< set w p bluetang
< AOK
< <4.41> 
> set w k 00000000000000000000000000
< set w k 00000000000000000000000000
< AOK
< <4.41> 
> set ftp address 198.175.253.161
< set ftp address 198.175.253.161
< AOK
< <4.41> 
> save
< save
< Storing in config
< <4.41> 
> reboot
< reboot
> $$$
< CMD
> show n
< show n
< SSid=ReefAngel
< Chan=3
< Assoc=OK
< Rate=12, 24Mb
< Auth=OK
< Mode=MIXED
< DHCP=FAIL
< Boot=0
< Time=OK
< Links=1
< <4.41> 
> get i
< get i
< IF=UP
< DHCP=ON
< IP=0.0.0.0:2000
< NM=0.0.0.0
< GW=0.0.0.0
< HOST=104.36.18.155:80
< PROTO=TCP,
< MTU=1524
< FLAGS=0x6
< TCPMODE=0x0
< BACKUP=0.0.0.0
< <4.41> 
> reboot
< reboot
Removing connection to COM9
---------------------------------------------------------------------
Your Reef Angel Wifi Attachment is now configured with the settings provided.
---------------------------------------------------------------------

If the blue LED is still blinking, it means that the Reef Angel Wifi Attachment could not connect to your wifi network.

Found router P9

Unable to setup port forwarding. This step will have to be done manually. For more information for your specific type of router, please visit http://www.portforward.com
I see the attachment connected to the router but I haven't been able to communicate with it.

How can i solve this?
Image
Top
rimai
Posts: 12857
Joined: Fri Mar 18, 2011 6:47 pm

Re: Wifi with 0.0.0.0 IP

Post by rimai »

It may be because your router is taking too long to return the address, because the first log showed it was connected.

Code: Select all

> $$$
< CMD
< DHCP in 6718ms, lease=259200s
< IF=UP
< DHCP=ON
< IP=10.0.0.80:2000
< NM=255.255.255.0
Is it still blinking blue?
Roberto.
Top
symon_say
Posts: 118
Joined: Sun Oct 09, 2011 6:04 am
Location: Dominican Republic
Contact:
Contact symon_say

Re: Wifi with 0.0.0.0 IP

Post by symon_say »

No, the green is slow blinking.
Image
Top
rimai
Posts: 12857
Joined: Fri Mar 18, 2011 6:47 pm

Re: Wifi with 0.0.0.0 IP

Post by rimai »

It should be connected then.
I can see the banner is updated to current time.
Roberto.
Top
symon_say
Posts: 118
Joined: Sun Oct 09, 2011 6:04 am
Location: Dominican Republic
Contact:
Contact symon_say

Re: Wifi with 0.0.0.0 IP

Post by symon_say »

I see is working now with making anything different, have been struggle with this for more than a week.

Thanks
Image
Top
Post Reply

Return to “Addons”