Reef Angel Forum

Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
> set u b 57600
> set s p 0
> save
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> factory RESET
< factory RESEô
< Set Factory Defaults
> reboot
< <2.38>
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Factory Settings Restored
---------------------------------------------------------------------

Opening Serial Port...
Verifying speed at 9600 baud
Connected to serial port COM3
> $$$
< CMD
> set u b 57600
< set u b 57600
< AOK
< <2.38>
> set s p 0
> save
< <2.38>
> reboot
Verifying speed at 57600 baud
Removing connection to COM3
Connected to serial port COM3
> $$$
< CMD
Wifi is communicating at 57600 baud rate

> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Wifi Attachment Connected to COM3
---------------------------------------------------------------------

Opening Serial Port...
Connected to serial port COM3
> $$$
< CMD
> ls
< ls
<
< FL# SIZ FLAGS
< 11 19 3 WiFly_GSX-2.23
< 30 1 10 config
< 31 20 3 WiFly_GSX-2.38
< 51 20 3 WiFly_GSX-2.38
< 71 1 10 user
<
< 184 Free, Boot=51, Backup=31
< <2.38>
> load user
< load user
< AOK
< <2.38>
> save
< save
< Storing in config
> save
< <2.38>
< save
< Storing in config
< <2.38>
> set o d ReefAngelWifi
< set o d ReefAngelWifi
< AOK
< <2.38>
> set w l 5
< set w þ%µ
< AOK
< <2.38>
> set w s SSID
< set w s SSID
< AOK
< <2.38>
> set w p password
< set w p password
< AOK
< <2.38>
> set w k 00000000000000000000000000
< set w mÈ00000000000000000000000000
< AOK
< <2.38>
> set ftp address 198.175.253.161
< set ft¸ address 1½8¿Ì³3™÷³wYw³îÃÏAOK
< <2.38>
> save
< save
< Storing in config
> reboot
< <2.38>
< reboot
> $$$
< CMD
> show n
< show n
< SSid=estanoche
< Chan=1
< Assoc=OK
< Rate=12, 24Mb
< Auth=OK
< Mode=WPA2
< DHCP=FAIL
< Boot=0
< Time=OK
< Links=1
< <2.38>
> get i
< get i
< IF=DOWN
< DHCP=ON
< IP=0.0.0.0:2000
< NM=0.0.0.0
< GW=0.0.0.0
< HOST=69.198.171.165:80
< PROTO=TCP,
< MTU=1524
< FLAGS=0x6
< TCPMODE=0x0
< BACKUP=0.0.0.0
< <2.38>
> reboot
< reboot
Removing connection to COM3
---------------------------------------------------------------------
Your Reef Angel Wifi Attachment is now configured with the settings provided.
---------------------------------------------------------------------

If the blue LED is still blinking, it means that the Reef Angel Wifi Attachment could not connect to your wifi network.

Found router SBG6580

Port 2000 is now being forwarded to 0.0.0.0

2.3.29 set ip address <address>
This command sets the WiFly module’s IP address, where <address> is an IP address
in the form <value>.<value>.<value>.<value> with <value> being a number between 0
and 255. If DHCP is turned on, the IP address is assigned and overwritten when the
module associates with an access point. IP addresses are “.” delimited.

get w

SSID=SSID
Chan=0
ExtAnt=0
Join=1
Auth=OPEN
Mask=0x1fff
Rate=12, 24 Mb
Linkmon=5
Passphrase=passphrase
<2.38>

get i

IF=UP
DHCP=OFF
IP=192.168.10.9:2000
NM=255.255.255.0
GW=192.168.10.1
HOST=192.168.10.9:2000
PROTO=TCP,
MTU=1524
FLAGS=0x6
TCPMODE=0x0
BACKUP=192.168.10.9