Litany of strange goings on...

skehole · Post by **skehole** » Fri Mar 24, 2017 5:30 pm

I have a variety of things currently happening and would love some assistance.

Switched router and modem and suddenly I could only access app from OUTSIDE my home wifi network.

To make things stranger I finally broke down and updated my wifi module and I can collect graph data and get them displayed in my home network and outside lte network, but cannot manipulate relays, or refresh my ph and temp while on my home network.

I recently switched from in code locations to internal memory on my ra+. All my relays are behaving as programmed according to my app, but my temperature changes (from 77.5-8, to 77-77.5)are not taking place according to my relay and graph data.

Let me know if there's anything further that is needed to figure out what's going on. I am not a tech savvy person. I am a tile contractor and work with my hands. I am starting to wonder if this platform was not the right choice for my skill set lol.

GugsJr · Post by **GugsJr** » Fri Mar 24, 2017 6:37 pm

Can you copy and post your code so we can make sure it's ok? Can you access the portal on the web? Are you trying to use the App from your phone/table?

rimai · Post by **rimai** » Fri Mar 24, 2017 6:40 pm

Did you also change internet provider.
I have comcast and cannot access my outside ip when I'm in my own wifi network.
They use a router that doesn't allow loopback.
I created two profiles on Android app.
One for when I'm home and one for when I'm outside.

skehole · Post by **skehole** » Fri Mar 24, 2017 6:56 pm

rimai wrote:Did you also change internet provider.
I have comcast and cannot access my outside ip when I'm in my own wifi network.
They use a router that doesn't allow loopback.
I created two profiles on Android app.
One for when I'm home and one for when I'm outside.

I did not change providers no.

Also, I went in to internal memory via the app, changed the temp parameters, then changed them back to where I wanted them and they seemed to recognize the new numbers for some reason.

I will post my code once my kids are asleep lol. Although it is EXTREMELY rudimentary and was solely generated through the wizard

skehole · Post by **skehole** » Fri Mar 24, 2017 7:00 pm

GugsJr wrote:Can you copy and post your code so we can make sure it's ok? Can you access the portal on the web? Are you trying to use the App from your phone/table?

Will post the code as mentioned previously but no, the portal will not allow me to change my relays.

Taken literally seconds apart

skehole · Post by **skehole** » Fri Mar 24, 2017 7:02 pm

here's the code

#include <ReefAngel_Features.h>
#include <Globals.h>
#include <RA_Wifi.h>
#include <Wire.h>
#include <OneWire.h>
#include <Time.h>
#include <DS1307RTC.h>
#include <InternalEEPROM.h>
#include <RA_NokiaLCD.h>
#include <RA_ATO.h>
#include <RA_Joystick.h>
#include <LED.h>
#include <RA_TempSensor.h>
#include <Relay.h>
#include <RA_PWM.h>
#include <Timer.h>
#include <Memory.h>
#include <InternalEEPROM.h>
#include <RA_Colors.h>
#include <RA_CustomColors.h>
#include <Salinity.h>
#include <RF.h>
#include <IO.h>
#include <ORP.h>
#include <AI.h>
#include <PH.h>
#include <WaterLevel.h>
#include <Humidity.h>
#include <DCPump.h>
#include <PAR.h>
#include <ReefAngel.h>

////// Place global variable code below here

////// Place global variable code above here

void setup()
{
    // This must be the first line
    ReefAngel.Init(); //Initialize controller
    ReefAngel.Use2014Screen(); // Let's use 2014 Screen
    // Ports toggled in Feeding Mode
    ReefAngel.FeedingModePorts = 0;
    // Ports toggled in Water Change Mode
    ReefAngel.WaterChangePorts = Port3Bit | Port5Bit | Port6Bit | Port7Bit;
    // Ports toggled when Lights On / Off menu entry selected
    ReefAngel.LightsOnPorts = 0;
    // Ports turned off when Overheat temperature exceeded
    ReefAngel.OverheatShutoffPorts = Port1Bit;
    // Use T1 probe as temperature and overheat functions
    ReefAngel.TempProbe = T1_PROBE;
    ReefAngel.OverheatProbe = T1_PROBE;

    // Ports that are always on
    ReefAngel.Relay.On( Port2 );
    ReefAngel.Relay.On( Port3 );
    ReefAngel.Relay.On( Port5 );
    ReefAngel.Relay.On( Port6 );
    ReefAngel.Relay.On( Port7 );
    ReefAngel.Relay.On( Port8 );

    ////// Place additional initialization code below here


    ////// Place additional initialization code above here
}

void loop()
{
    ReefAngel.StandardHeater( Port1 );
    ////// Place your custom code below here


    ////// Place your custom code above here

    // This should always be the last line
    ReefAngel.Portal( "skehole" );
    ReefAngel.DDNS( "fish tank" ); // Your DDNS is skehole-fish tank.myreefangel.com
    ReefAngel.ShowInterface();
}

skehole · Post by **skehole** » Sat Mar 25, 2017 12:15 pm

And never mind on the controllers int memory working on the heater.

GugsJr · Post by **GugsJr** » Sat Mar 25, 2017 12:22 pm

That's good to see.

skehole · Post by **skehole** » Sat Mar 25, 2017 7:05 pm

GugsJr wrote:That's good to see.

What is? Lol....am I missing something?

GugsJr · Post by **GugsJr** » Sat Mar 25, 2017 7:45 pm

Looks like your temps are working. They are going to fluctuate a bit because it takes time for them to go on and go off. You can set the range a bit lower then 77 if you want it to get to 77

skehole · Post by **skehole** » Mon Mar 27, 2017 12:50 pm

Why are my relays on the portal not reflecting the relays on the app?

GugsJr · Post by **GugsJr** » Mon Mar 27, 2017 12:57 pm

The labels? Or you mean you can't access the relays from the portal.

If it's the labels you have to change the names in the portal and download them to the app.

If you can't access the relays from the portals. Probably means your port forwarding isn't set up correctly.

skehole · Post by **skehole** » Mon Mar 27, 2017 3:59 pm

GugsJr wrote:The labels? Or you mean you can't access the relays from the portal.

If it's the labels you have to change the names in the portal and download them to the app.

If you can't access the relays from the portals. Probably means your port forwarding isn't set up correctly.

if you compare the two pictures I posted of my app screen shot and the portal photo, the auto, on , and off do not correlate from one to the other.

skehole · Post by **skehole** » Mon Mar 27, 2017 4:02 pm

And honestly, I don't care too much as I use the U-App exclusively but just wanting things to work either way just in case

GugsJr · Post by **GugsJr** » Mon Mar 27, 2017 4:34 pm

Oh I see that, honestly I'm not sure. Roberto probably would be the person you need help from.

rimai · Post by **rimai** » Mon Mar 27, 2017 7:18 pm

It says the last time you sent data to the portal was 3/23/2017, 12:33:07 PM

skehole · Post by **skehole** » Wed Mar 29, 2017 12:18 am

rimai wrote:It says the last time you sent data to the portal was 3/23/2017, 12:33:07 PM

That's strange seeing as how I posted the screenshot on the 24th. What would cause that to happen? Port forwarding is working on my U-App

rimai · Post by **rimai** » Wed Mar 29, 2017 10:45 am

Did you change code around that time?

skehole · Post by **skehole** » Thu Mar 30, 2017 8:58 am

rimai wrote:Did you change code around that time?

Yes I switched to internal memory coding. The code should be listed above. Also noticing that my graphs will not allow me to go beyond 1 or 12 hour time periods

rimai · Post by **rimai** » Thu Mar 30, 2017 9:37 am

It is because your last data was 03/23 and it only keeps for 7 days.
Tomorrow you won't have data.

rimai · Post by **rimai** » Thu Mar 30, 2017 9:38 am

I think it is because of the space on the ddns.
Try removing that space.

skehole · Post by **skehole** » Thu Mar 30, 2017 11:26 am

rimai wrote:I think it is because of the space on the ddns.
Try removing that space.

Can you show me where you're talking about? I assume it's at the end, but I'm not sure what space you're talking about.

Also, this was generated via the wizard and was not altered in any way.

rimai · Post by **rimai** » Thu Mar 30, 2017 1:27 pm

Yes, the space on your ddns line.

Code: Select all

 ReefAngel.DDNS( "fish tank" );

Use fishtank without a space.
HTTP protocol doesn't understand spaces.

skehole · Post by **skehole** » Thu Mar 30, 2017 2:40 pm

rimai wrote:Yes, the space on your ddns line.
Code: Select all
 ReefAngel.DDNS( "fish tank" );
Use fishtank without a space.
HTTP protocol doesn't understand spaces.

Gotcha. Thanks I will try when I get back in town.

skehole · Post by **skehole** » Fri Mar 31, 2017 1:09 pm

That appears to have done it. Thanks!

Reef Angel Forum