Reef Angel Forum

I sent a PM. Did you receive it?

The characters listed below are the only things printed on the teraterm screen.

Ðþÿþ

Everything loads with terterm. When the script is complete, I then try the wifi utility and it gives me an error, no blinking lights. The wifi screen says, Please wait, attempting to communicate with the Reef Angel wifi attachment. "Error" Please disconnect and then reconnect the Reef Ange...

Changing the baud rate to 57600 did not change anything. Still will not work with the wifi utility.

Just tried to use the script again, the following was shown on the screen.

à`Pqpàp >xðÀ 0 y`Ã}_~¹ý:þ÷þ EÜ(?ø>?Ѿû ýøÈþàwôô¾ÿÎ0¿?ðÿÿð
þð

So, there is no fix for the wifi unit?

There is nothing the screen is blank.

I have tried all of the above and still the wifi device will not connect. Any other suggestions?

Well, I guess that will be my next purchase.

Inevo, you are correct. My brain was seeing main relay box and my mouth was speaking head unit.

Rimai, can the 2 - 2 pin ports on the expansion relay box be used, when the same ports on the main relay box are being used by Jebao pumps.

I read that some where also. My ato is connected the main relay box. Can I switch them, as in ato to expansion box and dimming to main box.

It is stamped 8.1.

I don't know, I believe it is pwm. How do I find out?

Yes, but I can't get it to work. My light fixture just stays on all the time.

I have the 2- 2 pin connectors plugged into the expansion relay box.

yes

I purchased the Reef Radiance DM-165e with the upgrade kit for the reef angel. I have been trying to control the dimming with my Reef Angel+ and have not been able to figure it out. Does anyone have the experience doing this?

When I toggled my reef angel back on after a water change, my 2nd relay box did not turn back on. Any suggestions?

Hello ramai and fellow reef enthusiasts. I ran into an upload issue the other night and needed some help figuring it out. I have a RA+, 1 relay expansion I just purchased and 1 WiFi expansion. I can upload my previous code fine. But when I try to upload the new code for the relay expansion i get thi...

My LCD screen has quit working. It back lights, but no graphics or writing. What could be the problem?

Received the device yesterday and installed. The WP-40 now works. Will start working on the code this evening after work. Thanks.

Here is a picture of the inside of the box. I noticed 6 pins inside the box on same side where the two 2 pin jumpers are on the outside. I also included picture of those. What exactly am I looking for to tell if it has PWM?

Yes, I will open today when I get off work. The reason I think it's 2nd generation is i was referring to the Reef Angel0 Manual v1.8 page 6 and 7.

I believe I have the 2nd generation Relay Box. I remember the change was that the relay ports switched. The Relay Box I have has Port1 on the top right. Here is a picture of the bottom of the Relay Box. I measured the voltages on both 2pin connectors and they were both 0.5V. Here is a picture of it....

No. It is not even turning on.

Sorry, the reason I was asking is I cannot get it to work. I am only using one pump.

Hi, I know this topic has been posted alot, but I've searched through as many forums as I can find and I can't quite find exactly what I need in the code to get it to work. I just purchased one Jabeo WP40 pump from Reef Angel with the adapter cable included. Right now I have the AC power plugged int...

I figured it out. After trouble shooting for 15 hours, the first new float switch I tried , the ph probe would read correct ph in a glass of water and not in the sump, the second new float switch I tried, the ph probe would read correct in a glass of water and not in the sump. The third new float sw...

No. I unplugged it.

I noticed that the PH values from both my client and phone app were reading extremely low, (around 1.6.) So I cleaned it with vinegar and recalibrating the probe and PH still read low. I thought that my PH probe was bad so I bought another PH probe from ReefAngel. My new PH probe after proper calibr...