Reef Angel Forum

ok, moved the ground from dimmer to -v on ps. still no success. If someone can look at my wiring to make sure everything looks ok would be great. I think my jumpers are correct for 5v pwm. Maybe I should try taking that lone jumper off to change from 40 to 41? If everything looks ok, then I guess ne...

thanks Inevo, and does this ground go to the LDD boards ground or to the -v on PS, cheers

hi, do I use one or all three grounds on the dimmer expansion and does it go to one of the grounds on the Corolux 5up board or to one of the -v on PS? can you also explain why there are three grounds on the dimmer, thanks :D trying to get all my wires going to corrects locations and there are a lot ...

Does the dimmer need a dedicated 12v PS or can I use same 12V PS using for my 5-up LDD board? Or how about the one using for my fans? The PS is a 12v 2.0Amp model

I believe if you have a dimmer less than 6 months old it's jumpers for voltage Anol/PWM adjustment

for Albe and Sacehen, From LEDGroupbuy.com, using the LDD drivers. the 5-up board has ground for the LDDs There are also 4-2 boards available for smaller projects. All have ground built into boards. The 5-up has three grounds built in. "You can either connect it to the COM port on the power sup...

I'm going to be buying the CORALUX Meanwell LDD-H PCB Driver 5-up Board and it has a ground built into board I believe.

can I run Lumia 5.2 LED using LDD drivers straight off my ReefAngel PWM + version. Or do I need the storm X controller as well. I haven't seen a DIY forum using the reefangel and Lumia 5.2 build, but the forums I have seen, people are using a storm X controller on top of an Apex which seems redundan...

that's what it was. I thought it was part of a water tight compression seal because it was inside the PH probe plug and didn't look like a cap. I managed to pry it out and it plugged in. I think that fixed it. Cheers.

My first PH probe. I cant seem to get it onto its port. I have pushed as hard as I can and cant get it to lock onto the 2 tabs. I almost get it but the red rubber part seems to get in the way. It must be easier to put on than this. What am I doing wrong? The manual just says put it on but doesn't sh...

cheers, I will try that

I switched to the StandardATO from SingleATO. When using the SingleATO my ATO worked fine doing both on/off duties. For some reason using the StandardATO the lower float only turns relay on and doesn't turn relay off. The relay only goes off once the water puts the top float in up position. I'm usin...

thanks Roberto, I probably wait for official release of multi then. I saw you said few weeks in another thread, so I will hold off until then. Hope it passes tests. What's is look like for cost? Love to see one running/test in a video

Thanks Inevo, Does RA sell this multi level pressure sensor? If not which one are you using, any link?

I've been reading the thread "New ATO pressure switch-setup with Wizard?" and I'm trying to figure out which sensor would be best to use.

I see that Avast Marine ATO comes with the digital Reefangel plug. Has anyone used this?

http://www.avastmarine.com/ssc/do/produ ... op-off-Kit

Can the ATO Low port be used instead of High? I'm using the ATO High as backup for my pressure ATO.

Picture below so that it's clearer to understand. I'm currently using a Tsunami ATO, which uses a pressure sensor to turn on/off ATO. The Tsunami has a module which the pressure sensor 1/4 hose and water pump plug into. This module then plugs into the Relay Box. I also use high single float switch t...

I saw you were selling your BT bhazard. I guess you never got it to work?